dishwasher drain hose connector 3d models
91389 3d models found related to dishwasher drain hose connector.thingiverse
I had just recently installed a dishwasher in my home and I designed this clip to keep the drain hose secured above the garbage disposal. ...Fits a drain hose that is 20 mm in diameter.
thingiverse
My dishwasher drain hose (with 20mm OD) keeps kinking and blocking as it runs through a hole in the adjacent kitchen cabinet to get to the outlet. ...This thing protects the hose from the tight angle through the hole in the cabinet to the sink drain...
thingiverse
After discovering water at the kitchen floor, I discovered hole in the drain hose. I cut it and bought a drain hose at hardware store. Needed something to connect them together. This is a result of my quick design. Works good so far. ... My dishwasher...
cults3d
After discovering water at the kitchen floor, I discovered hole in the drain hose. I cut it and bought a drain hose at hardware store. Needed something to connect them together. This is a result of my quick design. Works good so far. ...My dishwasher...
thingiverse
After buying a new Bosch dishwasher I found that the drain plug was different from my old one. So that's it... Measured the tubes, drawed in sketchup, made and installed! ... I made it in Real-filament Bioflex.
prusaprinters
Fits 22mm (⅞ inch) drain hoses. Print the clips on their side with 3+ walls. ...Avoid over tightening as the plastic can split.</p>
thingiverse
This is a early version of a drain hose outlet for the BOB mini dishwasher by Daan Tech. As it is now, it's made to perfectly fit my specific sink wich happens to be from Ikea. Therefore it probably won't fit your sink to well. At the moment I'm...
cults3d
This is a early version of a drain hose outlet for the BOB mini dishwasher by Daan Tech. As it is now, it's made to perfectly fit my specific sink wich happens to be from Ikea. Therefore it probably won't fit your sink to well. At the moment I'm...
prusaprinters
This is a early version of a drain hose outlet for the BOB mini dishwasher by Daan Tech. As it is now, it's made to perfectly fit my specific sink wich happens to be from Ikea. Therefore it probably won't fit your sink to well. At the moment I'm...
thingiverse
... of the tapered screw. I have redesigned it summer 2019 and am offering it for sale here: https://smilingimpact.ecrater.com/p/33864416/air-conditioner-window-ac-drain https://www.ebay.com/itm/202702059487 https://www.ebluejay.com/ads/item/7335702
prusaprinters
It now drips into a garden hose and waters a raspberry bush. This thing can adapt to an air conditioning window unit's condensate drain hole. It's purpose is to help keep water from dripping freely beneath your window unit. Simply attach to garden...
thingiverse
This was a key dehumidifier part to drain the water to a floor drain, that does not require emptying the storage tank every day. I could not find a replacement part online and I did not want to buy a new dehumidifier just to avoid emptying the...
thingiverse
This is a connector to connect a washing machine drain hose and a smaller (~9mm) condenser dryer drain hose into a single drain. ... Print with supports.
thingiverse
simple washing machine drain hose siphon connector. ... Was going to buy it in the store, but got stuck in traffic jam, so came back home and designed it instead :)
cults3d
Simple washing machine drain hose siphon connector. You'd also need some simple rubber washer/seal ring to make sure there are no leaks when screwed on top of your drain sewer pipe. This being a critical part of your house, I'd recommend to print...
thingiverse
Tested with Daikin system, drain hole diameter 18mm. ... Need small support, only under pipe fitting.
thingiverse
:) --------- After servicing my Daikin outdoor A/C unit I noticed that my drain was broken, I made a copy of it and I am adding a triple fitting that can be used to connect the condensate drain of the indoor and outdoor units. As I didn't want to...
thingiverse
Customized version of https://www.thingiverse.com/thing:3764039 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=3764039
thingiverse
This clamp was designed to lock the dishwasher hose to the sink drain to prevent future problems. The clamp secures the hose using nylon cable ties, as shown in the picture. ... I've included the STL as well as the Fusion 360 export so that you can...
thingiverse
Hook for the dishwasher drain line under the sink. ... The drain line was getting the way of undersink storage.
thingiverse
The drainage was an issue as there was only the one spigot in the S-bend so I designed and printed this Y-junction drain for both dishwashers to connect to. Its been in use well over a year now so has proved reliable for both strength and heat...
thingiverse
Specifically made to fit Dux trap inlets but should work with the standard New Zealand and Australia drain spigots with an internal diameter 15mm Need an o-ring to seal, I used a 3/8" X 9/16' as that is what I had on hand. Metric equivalent should...
thingiverse
Edit 5-15-23: My models mistakenly had the drain chute about 4mm shorter than the design it was derived from, which works for my sink but likely not others. Posting original length (OL) versions. Recreated because I was having issues with the...
thingiverse
A simple fastener that holds the water and drain hoses of a dishwasher in place. It can be attached to the wall with double sided mounting tape. Requires two screws with a diameter of around 2.5 mm. The original Fusion 360 model is included. ...The...
prusaprinters
Replacement impeller for a Bosch dishwasher drain pump. ...Print with TPU.</p>
thingiverse
Simple bracket for mounting a garden hose or dishwasher hose using a single screw. See also the remix version of this with built-in cleats to avoid bracket rotation: This thing was made with Tinkercad. ...Edit it online...