diy makita track saw guide super simple by 3d models

Super Simple Guide for a DIY Track Saw Tracksaw is just a piece of Ply or MDF with a 12mm Alu Angle attached, This print keeps the Saw from drifting away from Alu angle. ... Slots into the Existing Guide slot on a Makita Saw and is secured by the stock...

These are the bushings to keep the slop out of a Makita track saw. ...When the print is done cut aa small slice through the ring vertically to let the ring expand when the screw is turned.

A simple connector that slides in the makita tracksaw rail T track, and allows connecting a DIY version of parallel guides. ...

Repeatable rips with the Makita track sawThis fence makes it easy to cut precise strips of exactly the same width when panel cutting. Two side fences are mounted on the guide rail for this purpose, and the required dimension is set via the...

Complete redesign of 3DDIY's nifty print-in-place guide rail holder. As I wanted to hang my rails on a garage door, I needed something a bit stronger and more secure. Also wanted to be able to mount these with the rubber strip facing up to avoid...

Complete redesign of 3DDIY's nifty print-in-place guide rail holder. As I wanted to hang my rails on a garage door, I needed something a bit stronger and more secure. Also wanted to be able to mount these with the rubber strip facing up to avoid...

You will need some M6 nuts and bolts and 2 rulers Blue Spot 33934 24-inch Aluminium Ruler https://www.amazon.co.uk/gp/product/B002HMQE86/ref=ppx_yo_dt_b_asin_title_o02_s00?ie=UTF8&psc=1 The rulers will need to be cut to show the correct dimension...

I made this guide for my Dewalt Atomic 4.5 inch circular saw. It allows it to snap onto a 1/8" by 3/4" aluminum angle screwed to a 1/2" board, and get nice straight cuts. You drill and tap the base of the saw and screw these on. I Used 12mm M4...

Simple holder for the tracks of the Makita track saw. Use 4,5 x 35mm wood screws for the `bottom` part. Use 4,5 x 20mm wood screws for the `top` part. ... Each part required 2 times.

https://youtu.be/XmLjWxxfME0 I designed a wall and ceiling mount for the Makita saw guide rail. ... Use metric screws M5x20 to button mount and 3.5 - 4 mm screws of the required length to fix the bracket to the wall or ceiling.

Hi there, here is my version of the festool / makita deflector. You just need to print the two files and to use M5 countersunk screw with its M5 nut. for more info: https://makeverse.home.blog/ I just posted the related article on my blog! ... ...

The spacing between the snapping tabs were increased by .7mm. Now it fits perfectly. ... I also changed the orientation so the front faces down on the print bed.

Remix from remix of db's excellent Dewalt Track Saw Guide from the PRUSA site. I made it so you can use it both at 90 and 45 degrees. Also I made the two retaining nuts into one. I hope this will add rigidity. ... Print instructions: No...

 Print the track guide with 0.3mm layer height, 4 perimeters, 15% infill, and without supports, you will likely need to clean out the holes where the nuts go. The guide rail has a fairly tight tolerance with the opening in the bottom of the...

... lift the saw. I designed a hose guide that simply clips onto the track and a saw-to-hose outlet adapter that has a smaller angle than the original. There is no need to hold the hose by hand. ... To assemble, use M5x20 hex head bolt and M5 nut.

This is a slide adapter to use your Makita Track Saw track with a Makita 196094-2 Compact Router Plunge Base. Requires two 1/4-20 nuts and short pieces of 1/4-20 allthread (or long bolts with the heads cut off). Drop the nuts in the slots and...

My contactor was using a track saw and I saw he had a duct-taped pipe fitting connecting his Makita track-saw to a Makita portable vacuum, and it kept popping off mid-cut. I slapped this together in Tinkercad and printed him one as a better...

This is an adapter to connect the Makita track saw to a 1-1/4 standard vacuum hose (shop vac or similar). I used "low quality" resolution since it's just a functional part. ... Took about two hours to print.

This adapter fits the outer diameter of the Makita XPS01PTJ track saw. The inner diameter from the vacuum hose is for a 1 1/4 inch connector. This fits perfectly on my setup with just the right amount of grip. Your mileage may. Purple,...

This is a dust cover for the Makita SP6000 corded track saw. It is not my design. Someone saw a picture of it on one of my designs and asked me if I happened to have the file and could re-upload it because Thingiverse seems to have deleted it. I...

Designed a wall storage for Kreg Track Saw Guide. ... I used a Strong Neodymium Disc Magnet 1.26" D x 1/8" H https://www.amazon.com/gp/product/B0772JGJDZ/ref=ppx_yo_dt_b_asin_title_o08_s00?ie=UTF8&psc=1 Added a wall storage for the Kreg Sled

I think I've worked out a pretty decent solution for a track saw guide rail rack that doesn't require any additional hardware. Every piece is printable with little or no supports. ...The only piece that I print with supports is the primary rack piece...

This adapter fits the outer diameter of the Makita XPS01PTJ track saw. The inner diameter from the vacuum hose is for a 1 1/4 inch connector. This fits perfectly on my setup with just the right amount of grip. Your mileage may. ...Purple,...

This cover/cap is for the Makita 18V X2 (36V) LXT Brushless 6-1/2” Plunge Circular Saw, model XPS01. The cover is very precise. ...It will keep dust from escaping through the side opening, thus improving dust collection.

This cover/cap is for the Makita 18V X2 (36V) LXT Brushless 6-1/2” Plunge Circular Saw, model XPS01. The cover is very precise. ...It will keep dust from escaping through the side opening, thus improving dust collection.

Thank you to https://www.thingiverse.com/Andcop who provided the version I remixed. ... I tweaked a few measurements by 0.1-0.5 mm to make it fit my Festool track without force.

They didn't necessarily need to be attached as they fit pretty solidly in the box but a bit of adhesive prevents knocking them around when the saw is not holding them down. I am including both the Fusion360 file and a STEP file so you can modify...

This should fit most track saw rails. Kreg and Bosch will need some editing to make those rails fit. You can divide the model in two or try to transform only the bottom half where the hook is. NOTE: When the print is finished the knob will be...

A little object for cutting at 90° with a festool track.

You'll need to have M5 bolt and nut. ...It super handy if you have an MFT style workbench