diy marker holder 3d models
365982 3d models found related to diy marker holder.thingiverse
**BOM:** *Printed Parts:* - (1) PCB Holder Body - (1) PCB Holder Front Body - (2) PCB Holder Clamps - (4) PCB Outer Spacers - (2) PCB Inner Spacers *Hardware:* - (4) 625 roller bearings - (1) 8mm (dia) x 125-150mm steel rod that is very very sharp...
thingiverse
This is a simple line marker for sports. Included also is some supports to keep the flag vertical and the legs at either 60 or 90 degrees. Designed to minimize the space in my sports go bag. I designed for my print bed which is 320mm but you...
thingiverse
marker holder lightboard DIY YouTube - https://www.youtube.com/watch?v=dKJfkPbI6k4
thingiverse
This Marker holder helps you organize your rendering markers. Can hold 18 markers. ... Compatible with Touch, Copic, and Deserre markers.
thingiverse
This is a marker holder for markers of .44inches in diameter. Holes are 0.5 inches wide and are offset, making back pens accessible. Holds 30 markers. ...Can be scaled to hold different size pens/markers.
cults3d
This is a marker holder for markers of .44inches in diameter. Holes are 0.5 inches wide and are offset, making back pens accessible. Holds 30 markers. ...Can be scaled to hold different size pens/markers.
grabcad
A 3D-printable marker holder. ...The measurements are taken from BIC whiteboard markers, as seen on the photo. (My 3D-printer had some issues, hence the bad quality of the printed marker holder)
thingiverse
This marker holder can be clipped at the bottom of a glass board and holds exactly one marker. The opening simplifies picking up the marker. ... Find this thing and its construction site also on [github](https://github.com/prandma/markerholder).
thingiverse
Stanford d.School Z-Board Marker Holder Instructions By using auto-desk inventor 2014 and a 3D printer
thingiverse
This marker holder has been created to hold eight markers. This Holder will stop markers from rolling off the table when kids are using them. ...Print Settings Printer Brand: MakerBot ...
thingiverse
Everyone knows RGB makes everything better. ...And a clean and tidy desk is a keypoint for a positive working environment. Now you can have both! With your markers and this simple marker holder.
thingiverse
... space. ...The first was a tape holder for her small rolls, and the second were these Marker Holders. The openings are 18mmx18mm that fit her larger Caliart markers, and will also hold her Copic markers as well. ...There are 60 openings for markers.
thingiverse
This is a holder for a common type of marker. Use a command strip or double sided tape to affix it to your fridge or other surface where you want a marker within reach. When you put the marker in place it makes a nice satisfying click sound. ... ...
thingiverse
... to spin on the tabletop. That was NOT part of the design but I'll take it as a serendipitous bonus. :-) This 100-marker holder may not fit on some printers. You may want to look at the [50-marker holder](https://www.thingiverse.com/thing:3419100).
cults3d
Whiteboard marker pen holder. The holder measures 88.5x 20.8 x 20.8 x 20 mm. Is designed for 16mm diameter markers. It can be scaled for other types of objects. ... I have anchored it with double sided tape but it has holes for fixing with 4.5mm...
prusaprinters
Very simple marker holder. ...I may revisit in the future to optimize for faster prints as this one can be a bit slow depending on settings. </p>
thingiverse
The holder can accommodate three regular EXPO markers, each boasting a 17.4mm diameter. I personally secure mine to my whiteboard using double-sided tape. ...To use this product, simply print the template and affix it to your board.
thingiverse
Holder for 80 dual tip markers that can be stored upright or on its side as shown. Tollerances are tight enough to hold whilst horizontal but loose enough to get out the pen of choice. ... Happy printing!
thingiverse
This marker holder takes around 1:30 hours to print and can hold markers, pens, highlighters and anything in between. It can be attached to a wall or a whiteboard for easy access. Print Settings Printer Brand: MakerBot ...
thingiverse
If we had a bigger printer, then the model can be printed actual size and work as a marker holder. How I Designed This I had to redesign this many times before I got the one that I ended up with now. The size was always too big. ...Then I got the design...
grabcad
This is holder, made from one metal sheet part and hold markers for a white bord, magnetic sponge and spray botle whit a cleaner.All this construction will be fix to the wall.Wall is visible on the pics.Job's doneEnd of the Story!