diy phone scanner stand 3d models
226998 3d models found related to diy phone scanner stand.thingiverse
To use the scanner you will need rubber bands and assemble all the parts according to the pictures. ...Place an object and scan it using your phone
thingiverse
The user places their phone on top and the document inside the box, then uses their preferred app to read aloud the page to them. Plastic bumpers are placed on top to guide the user to placing the phone in the correct spot (so the camera is above...
thingiverse
The larger piece is to help hold my phone steady above the slides. I have had great success using the SlideScan app by Photomyne. I printed this with PLA on a CR10 at .2mm, 20% infill, and with the tiniest bit of support for the 4 slide holder...
thingiverse
DIY QI Charger Phone Stand for the green 1.3in sq qi charger boards similar to this https://www.ebay.com/itm/115-49mm-Qi-Wireless-Charger-PCBA-Circuit-Board-With-Charging-Coil-Wireless/333707268234 no glue necessary may need to clip the spheres to...
thingiverse
A remix that includes a vise. «Cut a standard 25 mm PVC pipe to size, push it through the printed parts. ... [...] Optionally you can put M6 nuts and bolts to the parts but basically the friction between the parts are strong enough to hold the parts...
thingiverse
DIY 3D Scanner with Arduino. ... Parts requiered: -> Nema 17 Stepper Motor -> Arduino (any kind) -> Relay Board for Arduino -> A4988 Stepper Driver Board (100 micro farad electrolytic capacitor) -> 12V 2A Power supply -> 4 x Bearings 5 x 16 x 5...
thingiverse
This gives you more leeway in the distance between the scanner and the turntable, especially if you have trouble finding an IR sensor with a minimum distance of 2cm (most of the ones I found needed at least 5. For the full hardware specifications and...
thingiverse
Mobile phones are frequently used as a scanner. The apps are very cheap. The images are transfered to computer and internet via Wifi. Two problems remain: 1: Holding a mobile phone while scanning is troublesome. 2: Lighting condition needs...
thingiverse
Get started on making your own 3D Scanner with these STL files! A full set of instructions is available in Super Make Something Episode 8! You will need to print the following components: 1x scannerBase 2x stepperMountingPlate 1x shaftCoupler 1x...
thingiverse
Using an LCD-Backlight from any old display and a cheap china power-bank one can build an Iphone Photo Dia/Slide scanner!
thingiverse
This tripod holds your phone while using a scanner app to scan documents to your phone or iCloud storage. The legs are aluminium tubing 10mm diameter. One tube is 320mm and the other 2 are 280mm long. This will allow you to scan an A4 with an iPhone...
thingiverse
This thing was made with Tinkercad. ...Edit it online https://www.tinkercad.com/things/5pgS78lzbkv Simple stand for photographing documents. Stand was printed in ABS but PLA would work fine. ...Were made from 3/8" or 9.5mm Dowel
grabcad
... to obtain an electronic copy of those bills at home or receipts for Xero, rather than going through the scanning procedure. ...Designed for the Samsung Note 2, it could be used for any phone. ...Disassembles into 3 components and could be 3D printed.
thingiverse
das ist ein stative für einen sense 3D scanner. ...This is a scanner stands for a sense 3D scanner.
thingiverse
Just a basic stand for the autel maxisys automotive scanners.
thingiverse
Desktop stand for a Uniden (Bearcat) UBC3500XLT scanner, including a pocket to store a programming cable.
youmagine
This is a scanner stand for mobile phones. Cut a standard 25 mm PVC pipe to size, push it through the printed parts, lock the bottom part to the table using a bar clamp and you are done. Optionally you can put M6 nuts and bolts to the parts but...
thingiverse
This is a scanner stand for mobile phones. Cut a standard 25 mm PVC pipe to size, push it through the printed parts, lock the bottom part to the table using a bar clamp and you are done. Optionally you can put M6 nuts and bolts to the parts but...
myminifactory
This is a scanner stand for mobile phones. Cut a standard 25 mm PVC pipe to size, push it through the printed parts, lock the bottom part to the table using a bar clamp and you are done. Optionally you can put M6 nuts and bolts to the parts but...
prusaprinters
This is a scanner stand for mobile phones. Cut a standard 25 mm PVC pipe to size, push it through the printed parts, lock the bottom part to the table using a bar clamp and you are done.Optionally you can put M6 nuts and bolts to the parts but...
thingiverse
I update the Library Book Scanner Stand so that it now is totally 3D printed. Prints in 3 pieces. I print them with a raft and without supports. ...The new files all have v2 in the name.
thingiverse
So I designed a basic stand at a 40 degree angle with a lip for it to give me the best viewing angle. ... Print Settings Printer Brand: RepRap ...
pinshape
... it did not have a pull out stand. So I designed a basic stand at a 40 degree angle with a lip for it to give me the best viewing angle. ...Print SettingsPrinter Brand: RepRapPrinter: Prusa i3 Rafts: NoSupports: NoResolution: .2mm Infill: 40%
thingiverse
This is a basic stand/base for a Uniden SDS100 scanner radio. Initially this was designed for my own radio which has a small metal plate that I have secured to the back of my radio for mounting in my car so the internal dimensions were slightly...
thingiverse
This is a stand to hold a Raven Pro Scanner and give it a tilt to make it easier to see the screen and save desk room. This lifts the back of the scanner approximately 3 inches. You can still pull out both bottom paper trays while the scanner is on...