diy ps2 controller to usb 3d models

... 1122 mini ISO or 1115 mini ISO. USB Modules: USB-C + USB-A - SW3516 USB A x2 - MH-KC24 Available on AliExpress The Hilti B22 battery has a BMS that disconnects the modules if the battery is discharged, so the USB module will not damage the battery

Memory Card Holder for PlayStation and PlayStation 2 Cards. ...Engineered to match the exact specifications of the original bulky PlayStation 2 console.

This is a wall mount designed to be used with the console flat against the wall. Made to require minimal usage of filament. I used screws for wood, specifically ones that are 24.5 mm in length, have a screw thread diameter of 3.5mm and a head...

... in this project has been designed using CAD software, except for the MDF frame which wasn't printed. The idea was to create a small PlayStation arcade and it's still under construction. ...I'll keep adding photos as the project comes together.

This is a stand for 2 ps3 DualShock3 controllers with integrated usb hub. Im using a cheap (from ebay) usb 4 port hub - (last photo) to connect my controllers dongle. Assembly - 1 disassemble your usb hub 2 check if the down side of the PCB is flat,...

So.. ...as I'm a poor bastard and my PC mic broke, I decided to use the good old Singstar Mics I had. It's just a 35º stand, enough for the cable to be above the table. Hope you find it useful. ...;)

... difficult. The new model has a lateral spacing in relation to the console where a felt can be installed, in order to preserve the surface of the console. ...The side supports were positioned in the region outside the rubber feet of the console.

... but a dummy hole is also another thing. This is for anyone who dislikes the yellow sticker yet don't want to have any hole that may have something going inside, potentially break things up. ...This also make the backside more flushed and subtle

Bill of Materials: -Case: Top and Bottom -Eject button -2x Power/Reset buttons -Raspberry Pi Zero -Micro SD card -Mini HDMI to HDMI adapter, (remove the outer plastic shell with a hobby knife) -Micro USB Power Supply -USB hubman - take off the...

Mount that allows CP2102 to micro usb PCB to be screwed into enclosure. ... Three variants with different mount points (2mm holes) locations. All require usb micro connector to sit in some enclosure hole to be kept stable.

There were already some designs out there for NES USB Controller Ports, but they didn't quite Measure Up. So I Got Creative and Remixed the Designs, Crafting One that Would Seamlessly Replace the Existing Port and Allow for a Secure Female USB...

Never lose that usb to micro-sd card adapter again with this small addition to your 3d printer.

I designed it to be used without glue, only with the official usb cable supplied with the console! easy to print, there is no need for supports Follow the pictures for the setup, it's very simple! THE MODEL FOR THE DUAL SENSE :...

Full cheaper DIY KIT https://cults3d.com/en/3d-model/game/airsoft-ak-bullpup-mykolalop-3 (Part 1) DIY airsoft KIT for AK to bulpup Cyma AK 040 to bullpup. ... Parts list 4x m4 nuts 2x m4 bolt - 12mm 1x m4 bolt - 20-30mm 8-10x m3 nuts 8x m3 bolt -...

Hello friends This is a cabinet / box for a local available USB to Serial converter Category: Electronics

USB C to 3.5mm Jack Adapter Holder by UGreen - Attachable Keychain Accessory for Secure Storage and Portability.

Fully compliant USB 2.0 standard, backward compatible with USB1.1Support System: Windows XP, Vista, Windows 7, Linux, MacOS, and WinCE5.0 driveBaud Rate Range: 75bps – 115200bps, up to 6MbpsSupports Plug, Play and hot-swap ( USB side)Better than...

Remixed to fit necroware's builds bought from Tindie, as of 2023 (rev 0.2.1)These now use an Arduino Pro Micro with a USB-C port.You might need to use a needle file to open the USB porthole a tad.The recess for the Arduino board permits assembly and...

http://www.thingiverse.com/apps/customizer/run?thing_id=46423 Instructions Using the following options: Height = 5 manual y Build Plate Location = 100 Manual X Build Plate Location = 100 Pencil radius = 4 USB space gap = 6 Device Type = 5 Sign text:...

I ordered a pack of adapters from Amazon: https://www.amazon.com/gp/product/B07PH77NCL I needed a way to keep from loosing the little things. Print in TPU or other flexible filament. To install, pass the large side through the hole on the small...

Picked up a brand-new smartphone over the weekend, and I've already got a feeling it's destined to slip right out of my hands. Plenty of others have similar designs, but none seem to quite match up. ...Still, this one feels like a perfect fit - no need...

This stand is used for the controller I use for my PC, so I added in a small holder for the USB Bluetooth receiver, as well as a small cable clip for a charging cable on the back. ...I use this for my DualShock 4 controller, though it would likely work...

Here's what you'll need for hardware: - 30 M3 screws with a minimum length of 8mm - Four M4x8 screws and nuts (or M3 screws for securing the joystick) - Optional: four suction cups with M4 threads to prevent slippage I used the Zero Delay Arcade...

Case used to mount a [cheap USB to RS485 transceiver](https://www.aliexpress.com/item/32666986566.html) to a DIN rail.

You can build a DIY caliper for larger parts by combining these two pieces. ...Simply use a steel ruler of the right size or modify it to fit your existing one.

USB-C to 3.5mm Jack Converter Adapter, a simple and convenient solution for connecting your device to headphones or speakers.

Hello everyone, I'm excited to introduce this handy cabinet/box designed specifically for a locally accessible USB-to-Serial converter.

... There are several one-knob media controllers out there, but I've found no version that allows you to change tracks without dedicated buttons (like my larger [Arduino Pro Micro-based Media Controller](https://www.thingiverse.com/thing:2967216) has).

I'm creating a mock-up of an Apple USB to Lightning cable, primarily for designing accessories. ...The project is being developed using TinkerCAD and SketchUp.

The user requires a housing specifically designed for a USB-to-RS232 converter. ...After repairing the original enclosure, it unfortunately became irreparable, necessitating a substitute solution.