diy pulley 3d models
43616 3d models found related to diy pulley.thingiverse
http://www.thingiverse.com/apps/customizer/run?thing_id=16627 Instructions Using the following options: m3_nut_hex = 1 m3_dia = 3.2 motor_shaft = 5.2 nut_shaft_distance = 1.5 m3_nut_flats = 5.7 idler_ht = 1.5 retainer = 1.5 additional_tooth_depth =...
thingiverse
Multi-turn pot + dc gear motor + attiny85 w/ PWM input = 10-turn position pulley servo
thingiverse
This is a remade drive pulley to go with the linked e bike conversion. ...It has 6 spokes to be mounted on a 24 spoke wheel
thingiverse
Progress capture device for a lightweight pulley system for slacklining- I made one using 24mm ball bearing U shaped pulleys from Amazon and cut out some aluminum plates for the sides. ...This is the same width as the pulleys I used and simply bolts in...
thingiverse
Remix of Tom Stantons DIY Electric Bike pulley https://www.thingiverse.com/thing:2191603 I had clearance issues and needed the minimum possible overall depth. I removed the flanges and reduced the width to 15.5mm. I also decreased the thickness in...
thingiverse
This is a motor and pulley cover for the Torque Boards Motor Mount sold at https://diyelectricskateboard.com/collections/motor-mount-parts/products/50mm-motor-mount I was able to print using basic settings and NO STRUCTURE added, by printing from the...
thingiverse
Note: The 3D printed brackets/pulley were designed specifically for the bike used in the video, it will not fit any other bike and I will not be modifying it on request to fit to other bikes. Disclaimer: I do not hold responsibility for any wrongful...
thingiverse
These are the two pulleys. one with a 8mm hole for the axis' and one with a 5mm hole for the stepper. Feel free to ask any question. Instructions print the parts from ABS with a layer height...
thingiverse
Customized version of http://www.thingiverse.com/thing:343343 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=343343 Instructions Using the following options:...
thingiverse
Parts list: Motor: ALIEN POWER 6364 Motor 190KV £40 ESC: VESC V4.12 £63 Controller: Teensy 3.2 + ILI9341 LCD £30 Pedal Assist: PAS Sensor 12 Magnets £6 Bearings: 2x F688Z £1 Belt: 700-5M-15 HTD Timing Belt £8 Pulley: 5M 12T Timing Pulley £2 The...
thingiverse
Customized version of http://www.thingiverse.com/thing:343343 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=343343 Instructions Using the following options:...
prusaprinters
I've added the improved pulley body module and combined it with my own pulley body mod. This is only for use if you're using the DIY MMU2+1S mods. Print instructionsNo supports needed. ... Print using PetG for longer lasting and use 25% to 40%...
thingiverse
20T GT2 Aluminum Timing Drive Pulley For DIY 3D Printer With/Without Tooth Easy: video guide for beginnershttps://www.youtube.com/watch?v=PZkbPLquJnU Easy procedure for printing...
grabcad
20T GT2 Aluminum Timing Drive Pulley For DIY 3D Printer With/Without ToothEasy: video guide for beginnershttps://www.youtube.com/watch?v=PZkbPLquJnUEasy procedure for printing...
thingiverse
DIY DTG V-SLOT 20x80 BELT END BRACKET to hold an idler pulley on the receiving/platen end. Stabilizing pins/rails fit right into the slots for rigidity. I'm using this with a DIY DTG Epson P600... ... Pictures to follow, I wish this website would...
thingiverse
Customized version of http://www.thingiverse.com/thing:343343 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=343343 Instructions Using the following options:...
thingiverse
Customized version of http://www.thingiverse.com/thing:343343 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=343343 Instructions Using the following options:...
thingiverse
Customized version of http://www.thingiverse.com/thing:343343 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=343343 Instructions Using the following options:...