dji f550 hexacopter for sale 3d models
2295864 3d models found related to dji f550 hexacopter for sale.thingiverse
This part i have made to close the space room between the arms for my DJI F550 hexacopter frame kit. Six pieces around looks very pretty. The height of the part is 40mm. ...For fixing the wall part you put it between top and bottom plates.
grabcad
... FlameWheel frame. ... Includes two bottom plate designs that were available for measurement.This model was created as part of the 2019 NSF Student CPS Challenge. ... Motor and arm components were taken from: Open UAV for NSF student UAV challenge 2016
thingiverse
A Collection of some Parts for a FULL 3D Printed Hexacopter. ... (some parts i made at myself, other parts are from somebody else) parts i DONT made: https://www.thingiverse.com/thing:556185 https://www.thingiverse.com/thing:432598...
thingiverse
Railmount for DJI F550 Flamewheel. Holds two 10mm diameter carbon tubes with 58mm distance - e.g. ...for Feiyu-Tech Gimbals.
thingiverse
Finally I got my finished extensions for my F550 Hexacopter done. I tryed out different designs but I think this is the best and most stable on. With this extension you can use up to 12" Props on your F550. Hope you like it ! Print Settings Printer...
thingiverse
Here is a dome that I designed for my f550 Hexacopter. If you want to use it on another quad or hex then just scale it to fit. It has 4 pads that I use for mounting it with velcro. I used 10% infill 2 Shells .2 layer height. No raft or support...
thingiverse
This is a mounting ring for a dome cover of DJI F550 Hexacopter. Used dome cover you will find here: https://www.ebay.de/itm/Dome-Cover-Haube-fur-DJI-F550/262473285304?hash=item3d1ca07eb8:m:mrv4S3gOPOVX34AHpo1jFuA Ring is fixed on top plate with thin...
thingiverse
Holder / Rack for DJI F550 with retract the "connectors" werde designed for 14mm wooden strip. For the more common 13mm wooden strip, just scale it down to 97% ! you need to print this parts: 8x connect90.stl 4x connech180.stl 2x hold.stl 2x...
cults3d
Holder / Rack for DJI F550 with retract the "connectors" werde designed for 14mm wooden strip. For the more common 13mm wooden strip, just scale it down to 97% ! you need to print this parts: 8x connect90.stl 4x connech180.stl 2x hold.stl 2x...
thingiverse
Simple but strong mount for using 16mm landing gear with DJI F550 Hex. ...Not for F450.
thingiverse
A replacement Landing Leg for DJI F550 Drone. Same leg is used on the F450, i think. The original legs are designed to brake so I modelled this based of those. Only with two holes for mounting. ...Suits my project!
thingiverse
Super simple adjustable board camera mount for DJI F450 / F550 frame. I have a sony 600TVL camera (33mm) attached to mine. Uses M3 bolts and nylon nuts to keep things tight, although your board camera might fit only M2. M3 25mm x 2 M3 10mm x 2 M3...
thingiverse
Here is a set of addons for DJI FlameWheel F550. It consist of following parts: 3rd floor board to mount flight controller above battery. GPS/Magnetometer and companion computer may be attached there also. Bottom mount to attach Tarot FY680 landing...
thingiverse
DJI F550 Landing Gear was made from 2mm plywood at first. Then recreated it in 3D. Unfortunately my 3D printer is not capable of printing this yet but i will be enlarging it soon. Any advise and editing welcome. Please upload photos if you were able...
thingiverse
When I replaced the NAZA M auto pilot with NAVIO2, the GPS antenna mount went with the NAZA M, so I needed something that looks like it belongs on the F550. I think I did a pretty good first try. Any 5mm rod will do. ...I bought a length of carbon...
thingiverse
Designed to mount the XT90 connector to the F550 using the original screws.
thingiverse
This is a mount designed to secure the LED for the DJI Naza M V2 Flight Controller. This allows the LED to be mounted in the upright position. The mount locates between the upper and lower plates of the multi rotor. Needed some minor...
thingiverse
... used with O-rings with an inner diameter of 9 mm. ...Recomended that the water proof housing is used. Used gcardinal's DJI Phantom anti-jello GoPro-mount (http://www.thingiverse.com/thing:92014) and made a simple edit to add correct spacing for holes.
pinshape
Also build this custom box for my F550. Easy to transport with caster wheels attached underneath. I will see if i can find the DXF files and upload that as well. In cura please scale to 100. Sorry i dont know how to fix this problem. I am not good...
thingiverse
These are light weight and are great for protecting the props and in extreme cases you. Works with all DJI props from 8" to 10" in length. NOTE: SCALE UP 1000% Instructions Scale up 1000% to get...
cults3d
This extender increses the distance between the Gimbal and the base plate of your Drone by 5 cm, even giving room to the DJI Zenmuse Power Board Extension. It fits the DJI Zenmuse H4-3D or the old versions. The upper part fits any booms that are 6.6...
thingiverse
This extender increses the distance between the Gimbal and the base plate of your Drone by 5 cm, even giving room to the DJI Zenmuse Power Board Extension. It fits the DJI Zenmuse H4-3D or the old versions. The upper part fits any booms that are 6.6...
grabcad
this is a Nylon molded Multirotor Arm from the older Naza powered DJI sUAS.
thingiverse
A little idea I had for NinjaFlex filament... ...Should help reduce jello in your footage.