dji fpv goggles analog mod 3d models

Holder for an FPV Lens to work for the Avata. I used a Freewell ND Filter and it looks like it fits the space nicely. It is held on with friction. The clips don't hold yet but im looking to tweak it to see if I can get it to. ...It is very thin because...

... not obstructed by the print. Also trimmed off the excess parts so it fits seamlessly into the slot I had already cut out for the GoPro/FPV cam mount, which it replaced (https://www.thingiverse.com/thing:3266781). It's a snug fit. ...Printed in TPU.

DJI Phantom copy frame designed specifically for 1103 motors known as kingkong 1103 red. Comes equipped with a standard 20x20mm flight controller and is compatible with 1935 / 2030 props. The camera holder has been slightly customized to fit the...

I've designed some custom 3D mounts for the DJI air unit and its antennas that perfectly complement my building style, taking the Aquila 7 to a whole new level of functionality. Since I don't have an Aquila 5 on hand, I'm not entirely sure if these...

Remix of DJI Action 2 mount. Specifically redesigned to hold a 2mm perspex protective lens cover. I have broken the print into a flat packed arrangement that you superglue together after printing, this is to eliminate stringing from overhangs,...

I have designed this mount to accommodate big DJI air unit as well as leave space for CRSF nano receiver and cables under air unit. you need to mirror one of standoffs. ... My drone build: https://rotorbuilds.com/build/26791 My other GepRC...

TransTec is making DJI variants but moving away from their previous design decisions that lead to the Freedom v2. For this reason this frame is going to be a tight build. To make this build following components are needed: - iFlight Succex-A F4...

The Catalyst Machineworks Banggod is a quad frame build like a tank and if you don't mind it's weight than this frame makes for an awesome DJI build. To keep the weight to a minimum, the components are just the essentials to mount the DJI system. No...

This mount will allow you to mount a DJI Airunit above a flight controller in the Ranger (you will need to use a WSE sized controller) i am using the 765-wse. it hinges on the spar and allows for you to close the canopy just fine. Note that there...

All-in-one sled to hold DJI HD O3 camera, air unit, and antenna in a Heewing Ranger T1. Basic Notes:Utilizes existing rails for mounting points.Air unit is mounted on standoffs to allow the coax cable to coil underneath, and provide additional...

Custom DJI Phantom Copy Frame Designed Specifically for 1103 Motors (Kingkong 1103 Red) This frame is engineered to work seamlessly with the powerful 1103 motors from Kingkong, specifically the red version. The standard flight controller dimensions...

Вам знадобиться: викрутка з комплекту DJI інструмент для пластику або пластикова картка інтелектуальні здібності Ознайомтеся з налаштуваннями та можливостями принтерів, але, можливо, вам доведеться відрегулювати кути нахилу. У моєму випадку нічого не...

I designed a setup for a customer to utilize their TS58500 mini 5.8GHz FPV video transmitter with their Phantom 2 (equipped with Zenmuse 3D Gimbal). Note: You will need to fabricate a wire to connect the video transmitter correctly; this connection...

In my case, I opted for a RunCam 5 FPV Cam instead, but the results were just as impressive. The best part? This halter is surprisingly compact compared to some other models on the market. I was pleasantly surprised by its size, which made it easy...

I've been searching for a way to use the DJI airunit on my OG aluminum Armmattan chameleon, and I finally found designs that work for other models, but not for the NON TI version. I've made several revisions to these designs, and I believe I have a...

Compared to standard astronomer's goggles, they're slightly smaller in size. Two protective masks were crafted and some affordable sunglasses were sourced. The plastic lenses were then shaped to fit snugly within the lens holder. As a result, users...

Fatshark googles switch mod on door A(front left).No need to cut any connector or solder on fatshark original board.I designed a 3D printing new door to install a Switch with 2.1mm DC Jack( 2.1mm DC power socket with SPST black rocker switch).\r\nI...

I working with the complex surfacing tools in my CAD software (PTC Creo) to design shims which are tight fitting to the complex goggle surfaces and use the stock foam to seal against my face with nearly zero light leakage. I'm sharing these here so...

These goggles come in two versions, one utilizing the Raspberry PI HD broadcast project and a cheap dedicated 5 inch Raspberry Pi screen, while the other features a direct HDMI input suitable for an HD link such as the Connex Prosight. I designed the...

URUAV adapter for rapidfire (metal case and PCB with BEC):...

In order to reduce the weight on my DJI HD Camera, i replaced the main aluminium unit with a 3d-printed version. I copied the original 100%, so you can use the existing plastic bracket to mount the cable and keep it secure. There was another design...

I hope others can find this helpful :) Adapter: https://www.amazon.com/Receiver-Adapter-Digital-Fatshark-RapidFire/dp/B08LMWTBJ9/ref=sr_1_1?dchild=1&keywords=DJI+adapter+v2+analog&qid=1629098896&sr=8-1 DVR:...

Blocks air flow on front vents to create air flow in face area

https://www.thingiverse.com/thing:4441076 presented a thumb screw to replace the wing nut on the front-left corner of the BIBO bed. It is too wide for the other two positions. I have created a smaller version to fit the right-front corner and the...

Related videos:https://youtube.com/shorts/MIgc5CHgJewIt is designed to be used by attaching it directly to the original strap.Alternatively, it can be used on a 35mm wide strap.

Using hooks from <https://www.thingiverse.com/thing:2853261> This mount is very slippery. also doesn't fit ideally. ... I uploaded my Fusion360 model which you can edit to achieve a better fit.

I don't know this fact but I'm assuming it DOES NOT WORK UPSIDE DOWN. Made this with flexible materials in mind such that the battery holder won't pull hair. This is a VERY tight fit around the battery. You have to press it on and kind of a pain...

I was not able to find this top part reproduction anywhere, so I designed myself. Not tested yet. ...There are two version, one is with normal size, one is thicker