dji fpv mod 3d models
56217 3d models found related to dji fpv mod.
thingiverse
Remix of samabow's excellent thumber style stick ends extended to 20mm for more throw. ...Use 20mm m2 screw.
thingiverse
No supports needed. Transmitter could be held in place with a small amount of double sided tape. I left as much room as I could for cooling and included walls to direct air flowing under the camera to the transmitter. Install the antenna first and...
thingiverse
Frond Standoff has to be moved. ... Shock proof mount to use Rocksteady
prusaprinters
The parts were printed with PETg and the sideplates were fixed with double sided tape to the fuselage.The antennas lays flat against the foam of the fuselage and they are not able move in flight.The hatch closes without cutting any foam, no...
thingiverse
https://www.thingiverse.com/thing:4441076 presented a thumb screw to replace the wing nut on the front-left corner of the BIBO bed. It is too wide for the other two positions. I have created a smaller version to fit the right-front corner and the...
prusaprinters
<p>Based on the official design that comes with the TransTEC Freedom HD Frame (<a href="https://www.thingiverse.com/thing:3917318">https://www.thingiverse.com/thing:3917318</a>). However, I found that the original is too short, making the...
thingiverse
30x30 fan to cool the air unit. ... Use a cable tie to fix to the main spar outer tube and hold antennas in place
thingiverse
UPDATE BEGIN: It printed fine but does not work very well. The battery fits quiet loosely. I printed this part and it works much better for my application: https://www.thingiverse.com/thing:4950345 The battery is very snug, probably would be hard...
thingiverse
Original Author created a cool design I just added hole for M5 Nut rather than threaded insert. Original: https://www.thingiverse.com/thing:4799510 See original for all other settings. https://www.instagram.com/reel/CPh4fAIBfL5/ Is...
thingiverse
Human: High-Performance Hero 5 Action Cam Mount, Optimized for GEPRC MK4 Frame. ...Session mount is precisely angled at 26.5 degrees (25 degrees under maximum stress).\r\n\r\n\r\nThe final iteration boasts a reinforced base with increased thickness by...
prusaprinters
Easier mount by removing some antenna blocking part. ... Category: R/C Vehicles
thingiverse
Based on the official design that comes with the TransTEC Freedom HD Frame (https://www.thingiverse.com/thing:3917318). However, I found that the original is too short, making the wires/connectors hard to install. ...With the longer mount, the...
thingiverse
After my True-D receiver gave up from excessive mechanical stress, I replaced it with an AkkTek receiver (a reliable clone) and created a custom housing based on innovative ideas found at https://www.thingiverse.com/thing:4316407. To minimize force...
thingiverse
Researchers discovered that removing the lid enhances its overall performance significantly.
thingiverse
This file works well for the Nano Goblin printed in TPU. Can be used on just about any wing. Does cut off the image a bit for protection, I took my soldering iron to it to flatten it out in the high spots. ... https://youtu.be/eb75F_m_VeM
thingiverse
Easier mount by removing some antenna blocking part.
thingiverse
hi this is a mount i remixed for the vortigaunt its not a perfect fit on the frofiles of the vorti nose but does the job very well
thingiverse
This is the mount for a 5.8Ghz 40ch 600mw Skyzone TS832 transmitter. The plate mount attaches to a Walkera G-2D Brushless gimbal. The plate and transmitter are secured using a zip tie. Print Settings Rafts: No rafts are used. Supports: There is no...
thingiverse
This is a mounting solution for an additional forward-facing camera when capturing dual-mode footage. ...Print Settings Rafts: No rafting required Supports: Enabled for added stability Resolution: Set to 0.20mm for crisp detail Infill: 10% infill...
thingiverse
Print with 4 walls 100% infill. I printed these in Petg. The shock tower mount bolts on using the stock suspension mount bolts. Bolt head is recessed to ensure there is still enough thread to put the lock nut on securely when you put the suspension...
thingiverse
made this for my X-maxx but you could put it in any RC. cut a hole in windshield and mount on the inside. put a some clear acrylic in front to protect from water. Also has a mount for a standard 30mm fan cus damn caddx gets hot. Let me know if...
cults3d
Better Head support from the original. Original site: https://ethixltd.com/portfolio/ethix-goggle-strap-v2/ Nozzle Temp: 210 Bed Temp: 65 Need good clean of the supports. ... Print Settings Printer brand: Creality Printer: Ender 3 Pro Rafts: No ...
thingiverse
This Air Unit mount swaps out the original rear standoffs with a sleek new design. ...Assembling it is a breeze, and its lightweight construction puts minimal strain on the sensitive MMCX connectors, all while keeping the overall weight down to a mere...
thingiverse
it's remixing the battery case with a more precise fit Use two 21700 battery and 3 pcs M2x7mm (or longer) change: thinner and wider shorter by a couple of millimeters the smaller button version with holes and full case add: the groove...
thingiverse
This has been a remix of 2 different designs. I wanted a detachable uruav analog adapter v2 case, which worked with tbs fusion. Also I've added a link to a power cable clip just for completeness sake. I've tucked the cable in reverse so that it can...
thingiverse
A simple battery holder for goggles V2. Holds very well in place, ultra light If needed, to get better clip, you can warm it into hot water and bend slightly the clip. ...