dji fpv mods 3d models

This is built from a frame designed by https://www.thingiverse.com/ledroneclub/designs Frame-> https://www.thingiverse.com/thing:4660219 I ordered the frame custom cut from Cncmadness https://www.cncdrones.com/ /...

Low Drag FPV Nose for Multiplex Funjet Ultra 2 designed to fit DJI HD FPV Camera. This nose also fits the regular funjet 2 and old funjet and funjet ultra! Cutting the nose off a funjet straight is not an easy task, but I came up with a method that...

I simply designed my drone to deliver a seamless digital FPV experience for my compact Dart RC plane.

All Parts needed to convert the AmaxInno F4Mini Frame from analog to the DJI 03 AirUnit.With 4Inch the Props are not in view and because of the softmounting the stabilization works as intended.Print parts lay flat.

It's 280 gram quad 9x9mm motors, with 4s 850mah battery, 7 mins fly. ... Motor: xing 1404 3800kv I designed for dji o3 air unit and tbs crossfire nano rx. ... It needs 4 m3 30mm spacers, a lot of m2 6mm 8mm 15mm screws

This is a simple DJI cam mount to be directly mounted on a "naked" Caddx Vista. The slight elevation compensates for the components on the Vista board. ... You can find the fitting cam sleeve here: https://www.thingiverse.com/thing:4622139

(from DJI motor to stock brushless motor) * adapter hight 5mm * printed with PLA and 100% infill * Motor C-clip is running smoothly * Motor shaft is running smoothly What you need: * 2x M2,5 screw (through the carbon frame>adapter) * 2x M2,5 nut *...

We've got a new accessory to take your Dji HD Cam to the next level! With a standoff width of 26mm and height of 25mm, this mount fits perfectly into worn-out frames for both 3" and 4" cameras. Printed with TPU and HoneyComb infill at 238-235° and...

just a dji air unit, caddx polar/19mm wide camera friendly roof rack/camera mount for the traxxas 1/14 e-revo. ... all the side hardware is m2.5 x 6 to m2,5 x 10 and the through bolts holding the bottom portion to the top rack are m2,5 x 10mm all...

Pressfits the dji air unit and holds it in place with a ziptie, that leaves all ports available. Has space underneath to route the cables to the front. Light weigh design with many gaps to prevent heat build-up. ... You need: 4x M3 nut 4x M3 6mm...

This is a 3D printable tray designed for the DJI Air Unit. This needs a strap to keep the Air Unit in place but makes mounting the Air Unit and Camera onto a model a lot easier. I have also included the small clips that I use to secure the...

The other two things I also modified from the DJI antenna holders model (https://www.thingiverse.com/thing:3919933) and the TBS immortal-T antenna holders model (https://www.thingiverse.com/thing:3400170). The original immortal-T antenna holders...

Just install the "base" and wiring to the FC on your models and fit the FPV Pod to the model in current use. Compared to the pictures the locking system has been improved and simplified in the stl files.</p><p>A mount/air scoop for the Heewing T1...

Just my design to enable digital fpv experience for my little dart rc plane :) Print Settings Rafts: Doesn't Matter Supports: Doesn't MatterResolution: 0.2 Infill: 30 Filament: n/a petg Category: R/C Vehicles

DJI URAV PCB v2 Analog Adapter for TBS Fusion - A Perfect Fit? I'm Not So Sure. I've been wondering if this adapter will fit other modules, and after careful consideration, I'm guessing it should. The module slot always has the same form, so it's...

- DJI Mount_M3 Screws.STL -> this one will work with normal M3 countersunk screws which will self thread into the plastic - DJI Mount_M3 Inserts.STL -> this one has larger holes and is thicker so M3 inserts (M5 outer, M3 inner thread) can be used...

Mount for DJI Action 2 camera. Some generic and specific versions are available (case only, GoPro mount, Apex Mount etc.) Print on the (right) side for better sturdiness. Specifications : - Good camera protection (2.5mm walls) and bumpers -...

Just install the "base" and wiring to the FC on your models and fit the FPV Pod to the model in current use. Compared to the pictures the locking system has been improved and simplified in the stl files.Now there is also a .STEP file of the base so...

This is my first 3D design. It´s bad I know but it does the job. Hope some one will take the idea further. ... I printed in PETG but thing PLA or ABS might be better.

I was angered that DJI wanted to charge another $15 for foam to make them fit properly. I resolved to spend as much time as it took to make 3D printed parts to adapt the goggles to my face. I started with some of the other shims on Thingiverse,...

The principal is that it keeps your FPV Camera always perfectly in line with your GoPro no matter the angle you set. Because of limited space in the Shocker design, This mount only allows for 2 angles... steep and mellow... which works well for me....

For my setup, the mounting holes for the DJI O3 AirUnit at the back of the Rotoroma Buddy frame were too far to the back, so that my camera cable was not long enough.I am flying the Rotoroma Buddy 5" Deadcat, but my model should work with any...

Probably not best for bando bashing but great for cinematic.Step 5: Bolts & Base OptionsBase Thickness:Standard is now 3.4mm thick. Thick is 4mmBolt style:Standard size for M3 bolts is a 6mm diameter bolt-head.Perfect for nearly all M3 bolts and...

Original PLA holder was too lose, i redesign it and print with TPU, now they awesome. ... Appreciate to sub my channel: https://youtu.be/qYj2IyVemuQ

<p>TPU</p> Category: DIY

UPDATED: Some people tell me there is some variation between X-Air Antenna. I have give about 0.5mm of room to the Brackets. Please tell me if everything is fine. Since I use oly one X-Air antenna with two omnis, I decide to integrate the...

Need 2 screws to assemble part1 and part 2. Pls post your makes. ...thx

Easy replace. Keeps the strap more uptilt for more comfortable wearing. I recomment printing in strong PETG or TPU (PLA may deform in sunny conditions). [Upcomming update will be a solution to route and strain relief the powerwire to prevent...

The 3D model was created on real base. ...It’s created accurately, in real units of measurement, qualitatively and maximally close to the original.

Modified design updated to suit FatStrap branded Headband. Battery is very stable and includes "End Caps" to keep the battery in place and assist de/activation while googles are worn. Update remodelled over a few iterations for user-friendly...