dji naza v2 download 3d models
216138 3d models found related to dji naza v2 download.thingiverse
Weight frame: ~ 160g (lighter than the F450 frame which is ~ 280g) total: ~ 1250g My setup, other hardware F450 combo kit (NAZA-M-v2 + E305) Folding propeller Hélice Para Dji Phantom 3 9x4.3 9450 Transmissor E Receptor Eachine Ts832 Rc832 Boscam 5.8g...
thingiverse
Then I designed the foldable drone around the legs, DJI Naza V2, PMU, LED, 4500 Turnigy battery, Turnigy 9X receiver. I used the Multistar 2213-925 motors ith 1045 blades and Turnigy esc's. Used a foldable antenna holder for the receiver and GPS. It...
thingiverse
This is a addon to my prev. ...design for NAZA V2 equipment. It's the for GPS, VTX and Receiver mounting. Usage is self explained. ... Have fun...
thingiverse
Created the guard for the DJI Naza V2 GPS sensor so it can stand up to an impact better (hopefully). I also made a stand which is slightly shorter than stock and can break in an impact to reduce the force on the sensor to again help it stand up to...
grabcad
Bought the Dji Naza-M V2 and remodeled it as used as design intend for creating new multirotor applications. ...This model was created in Creo Parametrics.
thingiverse
To mount DJI Naza V2 GPS Compass inside it to replace the existing long metal holder which is to long and can't fit inside my quadcopter case. The mount is elevated by 5cm instead of laying flat on the quad, and also provides space to wrap remaining...
thingiverse
This is a mount for the NAZA_M V2 controller so i could bolt it to the F450 lower frame stock holes. All the other items on the quad can be found under my name. ... Instructions I printed this at 50%...
thingiverse
Support to put the DJI Naza-H LED on the Align T-rex 450 SE V2
thingiverse
This is a mount designed to secure the LED for the DJI Naza M V2 Flight Controller. This allows the LED to be mounted in the upright position. The mount locates between the upper and lower plates of the multi rotor. Needed some minor...
thingiverse
I've designed a Mount for the Status-LED of the DJI Naza M Flightcontroller. It is designed to mount your LED at the back of your aircraft facing in a nice angle down to you for maximum visibility. ...It can be attached with some 3M Tape wich is...
thingiverse
Do you have an old DJI naza flight controller unit? But you want mount it to 30x30 pattern? Here is a mount for it. ...Just use a standoff with short pins and plastic nuts to squeeze between the gaps.
cults3d
Do you have an old DJI naza flight controller unit? But you want mount it to 30x30 pattern? Here is a mount for it. ...Just use a standoff with short pins and plastic nuts to squeeze between the gaps.
thingiverse
This is a mount I made for the NAZA_M V2 PMU V2 so I could mount it to the side of the bottom plate on the F450. All the other items on the quad can be found under my name. Instructions I printed...
thingiverse
Soporte para instalar la Naza con el receptor de DJI en el AquaPhantom
thingiverse
A mount support for dji naza gps, to install the gps + compass module into a drone frame. ...https://github.com/Scicrop/flameweel-parts Print Settings Printer: 3DCloner DH ...
thingiverse
A Naza mount with or without GPS, depending on the top plate you choose. Bolt holes are 3.1mm for M3 tread. Spaced 45mm center tot center. Dimensions are 52 x 52 mm. Height depends on top plate. ...Work in progress.
thingiverse
Template for DJI NAZA v1/v2/Lite flight controller and accessories. ... Designed with Designspark Mechanical (file included).
thingiverse
This is a equipment holder for DJI Naza V2, miniOSD and PMU V2. ...I used this in center of an DJI F550 Flame wheel top plate.
thingiverse
Lightweight but sturdy holder for the LED module of NAZA-M V2 Flight Controller System (should be the same for the Naza Lite version). Fits snugly around a Dji Flamewheel arm with tie-wrap holes to hold it securely to the frame. It's a pretty...
thingiverse
Very useful GPS module protection for DJI NAZA A2. It already saved GPS module of my friend while crash. ...It best used with soft material on the inner side.
thingiverse
Dies ist eine Halterung womit die GPS-Antenne der DJI NAZA einfach befestigt und gerade ausgerichtet werden kann. You want it, but you have no 3D-Printer?? ... Ask me: 3D-Printshop@gmx.de or take a look...
pinshape
Купил Naza v2 и решил её смоделить для сборки квадрокоптера в 3d. ...Используйте и вы) Буду моделить и остальные модули I bought Naza v2 and decided to model it to build a quadrocopter in 3d. ...Use with pleasure) I will model and other modules
cults3d
Купил Naza v2 и решил её смоделить для сборки квадрокоптера в 3d. ...Используйте и вы) Буду моделить и остальные модули I bought Naza v2 and decided to model it to build a quadrocopter in 3d. ...Use with pleasure) I will model and other modules