dji phantom 3 ipad mini 3d models
834189 3d models found related to dji phantom 3 ipad mini.thingiverse
The iPad Mini (all versions are the same size) slides into the visor and the whole thing is then clamped onto the DJI RC unit. The idea for this design was to make it light weight, so the walls of the visor are only 1mm thick (as designed). The...
thingiverse
Ive not printed it so issues are yet unknown This is a remix of Tetralites DJI Phantom 3 iPad Mini Sun Visor. I added thicker sides at the points where the iPad slides in to prevent splitting. I also added a cut in the cross brace where you can put...
thingiverse
I remixed this to hold the iPad Mini. This will work with all generations of the mini. Make sure to print with supports everywhere. ...Print Settings Supports: Yes
cults3d
I remixed this to hold the iPad Mini. This will work with all generations of the mini. ... Make sure to print with supports everywhere.
thingiverse
Hello! ... This is a small temporary small extender to use your dji phantom 3 standard with an ipad mini. ...It works well and you don't need support,infill and you print it at 0,2mm Hope you enjoy
thingiverse
made this bracket to fit my ipad mini which is in a lifeproof case too fit on the Dji phantom hand set. ... https://youtu.be/M6zYJAGwwIY
thingiverse
Phantom 2/3/4 Sunshield for various Configurations (iPad mini). Don't print SSW-Full.stl, it is only for assembling... ...Let me see, what You have printed...!
thingiverse
It's a iPad 2 3 4 holder for Phantom Dji Standard. ...And it already has support Just print in 0.3, and cut out all the support
thingiverse
This clip can be used with other clip or clamp holders but I modeled this one specifically for the DJI Phantom controller's clip that was for an iPhone sized device. iPad Mini holder/clip. If you make one, please post a Made :) Work done at the...
thingiverse
This is a custom visor/clamp assembly to work with a iPad mini (1, 2 and 3. Not sure it it will work with a 4) in a LifeProof or Otterbox case (Visor base included for both cases). The clamp assembly uses the stock hardware of the remote. It will...
thingiverse
just make it a bit fat, correct some aberrations, remesh and add dji logo,also its necesary to fit some slide cotton stripes to secure the ipad on the mount,now works really fine, hope everybody enjoy it.
pinshape
SummaryIt's a iPad 2 3 4 holder for Phantom Dji Standard. ...And it already has support Just print in 0.3, and cut out all the support
thingiverse
I found the flysight black pearl design and modified it to hold the iPad mini. You may need to use some foam tape around the insides of the bracket on your iPad. Note, I have recently printed this on my IIIP and it came out very nice but the iPad was...
thingiverse
I have made 2 designs for iPad mini that attaches with the Apple Smart Cover or Case and another one without cover or case. ... I printed on Da Vinci 1.0A with the following setting : Layer height : 0.2 3D Density : 0.15 Shells : Standard Any...
thingiverse
I designed this case for use with CPU intensive drone apps such as Drone Deploy, where my iPad mini 4 is often exposed to direct sunlight and summer temperatures while complying with visual line of sight rules. So far tests have proven to be...
youmagine
3 Parts: Mount for the Clamp, Top Holder where the Off-Switch resides and the Bottom Holder. ...Mount them correctly or it will always press the Power Switch!
thingiverse
... shade I designed in OpenSCAD. ...It fits over the top of a full-sized iPad. Designed for use with the DJI Phantom 3 Advanced or Pro controller, but might work with other units as well. ...OpenSCAD source file uploaded as well if you want to tweak it.
grabcad
... splicing in the 5V tap on the USB cable to leave the signal wires (white and green) shielded. Note: The cooler is designed so that the whole unit with iPad attached can fit inside the iPad recess in the hardshell carry case for the Phantom 3 pro.
thingiverse
This is a DJI Phantom replica body for the Hubsan x4. This is still a work in progress. Consists of two halves that will need to be fastened together with some small screws or rubber bands. The camera is designed so it can be mounted facing forward,...
thingiverse
This is a great little iPad 2,3,4 holder to mount to your DJI Phantom 3 standard controller. This is based off a remix but removed support and rebuilt with watertight manifold so it's ready for slicing. Happy printing / flying :) Print Settings...
sketchfab
This is a highly detailed version of the DJI Phantom 3 Pro for Element 3D Product Link: https://store.cgduck.pro/element-3d/dji-phantom-3-pro-e3d.html
sketchfab
Made DJI phantom 3 for online class. used 3ds max and painted with substance. ...hope you like guys.
thingiverse
Just install Your iPad Mini onto the included Smartphone Holder which comes with the Phantom 2 Vision Series Quadcopters. ...Beware of the Power Switch and install the iPad Mini correctly or it will be pressed continously!
thingiverse
Kennzeichnungshalter für Drohne DJI Phantom 3 KENNZEICHENSCHILD bei www.3dcreativ.de in 40x20x1mm erhältlich. Besichtigung der Drohne mit Halter im Küstencamp. ... www.kuestencamp.de
myminifactory
Clamp for DJI Phantom 3 With this clamp you can attache using velcro tape some carriage. e.g. ...a such as a strobe light etc.
thingiverse
Revised the Ipad holder vertical mount so that it can be used with a Range Extender https://www.thingiverse.com/thing:1096728 on the DJI Phantom 3 Standard with the single antenna. I also slightly re-shaped the mount where it contacts the transmitter...
cults3d
Revised the Ipad holder vertical mount so that it can be used with a Range Extender https://www.thingiverse.com/thing:1096728 on the DJI Phantom 3 Standard with the single antenna. I also slightly re-shaped the mount where it contacts the transmitter...