dmx controller 3d models
86827 3d models found related to dmx controller.grabcad
Since some months i work on a DMX RDM splitterthis one is 1 IN / 8 OUTall the PCB are validate
thingiverse
Here is my case for the 16 Channel Relay DMX Board. ... You can get it on AliExpress.
cults3d
Are you tired of having your SUSHI permanently disconnected? ... Here is THE solution, an innovative clamp to hold your Nicolaudie DMX sushi and its cables! A durable and innovative solution! ... 4*M3*30 1 Rislan
thingiverse
This is a remix of kefke44's DIY DMX Box that allows a generic "Chinese" wireless DMX module to also be fitted. The wireless board was fitted to the lid using 7mm plastic standoffs. Being that close to the lid meant that the holes for the wireless...
grabcad
Application LED réalise des régies lumière sur mesure.Ici un modèle trois univers sur une base PC avec interfaces SUNLITE.Une console DMX 512 16/32 est aussi présente.Trois écrans PC dont un tactile au centre afin de lancer les scénes.
thingiverse
This is a carrier for Hendrik Hölscher's DMX transciever. Link to his site for the Transceiver hardware: http://www.hoelscher-hi.de/hendrik/english/led.htm Transceiver by Hendrik Hölscher. MakerBot Compatible. ...
thingiverse
----------------------------------------- **[PT-BR]** Caixa para módulos DMX sem fio com aberturas para passagem de fios e antena. A caixa foi projetada para ter um fechamento de encaixe simples e de fácil manuseio, pode ser feita abertura na tampa...
thingiverse
http://www.thingiverse.com/apps/customizer/run?thing_id=1264391 Instructions Using the following options: Vent = 1 FootDia = 7 BPanel = 1 Height = 45 PCBWidth = 53 TShell = 1 txt = DMX to MPX m = 0.9 Length = 140 Police = Arial Black PCBPosY = 15...
thingiverse
This cap works on most XLR ends, I made it specifically for DMX and it works with both the 3 and 5 pin variant. It would work perfectly for 3 pin XLR connectors for audio. This will only fit on female cable ends! To put it on line up the notch on...
thingiverse
The DMX-40 Transceiver from PreppComm does not have a stand. They do offer one at an additional cost. Theirs did not meet my needs. I wanted a stand that would grip the radio. Mine is wider and clips on radio. These stands (2 required) take 4...
thingiverse
This is a case for a small DIY project: A USB to DMX adapted for lighting control following this guide: https://stevenbreuls.com/2013/05/diy-usb-dmx-dongle-interface-for-under-10/
cults3d
... decoder from banggood. https://www.banggood.com/3-Channels-DMX-RGB-Decoder-Dimming-Controller-for-LED-Strip-Light-DC12-24V-p-1150606.html?rmmds=myorder&cur_warehouse=CN and I finally made a housing for that. ...have fun with it if you can use it.
thingiverse
... from banggood. https://www.banggood.com/3-Channels-DMX-RGB-Decoder-Dimming-Controller-for-LED-Strip-Light-DC12-24V-p-1150606.html?rmmds=myorder&cur_warehouse=CN and I finally made a housing for that. have fun with it if you can use it. ...
thingiverse
DIY USB DMX Interface for under $10 https://stevenbreuls.com/2013/05/diy-usb-dmx-dongle-interface-for-under-10/
thingiverse
DMX Stand for Stairville DMX-Master to use it with Pioneers CDJs. Print it top down with the glue side on the 3D printer glass surface, no rafts or supports needed. ...The stand could be fixed with a carpet tape.
thingiverse
----------------------------------Deutsch------------------------------------------ Eine DMX Box zur Wandmontage. Die DMX Kabel können von oben zum anlöten eingeführt werden (max 10mm). Es muss als erstes das Kabel durch die vorhergesehene Öffnung...
thingiverse
I needed an ident for each of my DMX connectors on my home made encoder wing. ...This is a generic ident for an XLR chassis connector.
grabcad
A cover panel, a 18mm tube mounting support and a ring for the push button for my DMX RGB plastic box (Arduino Project Hub)
thingiverse
The Box based of the Customizable Round Box with Lid from Arvin: http://www.thingiverse.com/thing:189264 It is the home for an AVR ARTNET NODE, DMX Wireless 433MHZ (both from http://ulrichradig.de), 2x Female DMX Plug Adaptor and a power stepdown.
thingiverse
This is a small enclosure for the Enttec USB to DMX widget (http://amzn.to/2GkIcdC), these adapters can be bought quite cheaply without a case, this 2 part 3D model solves that. The DMX module fits snugly inside and the top pushes into place holding...
thingiverse
DMX Termination Tool, Clip Style - for use with ETC's new DMX connectors being used in many of their products in 2023+. This tool allows the spring clamp to be depressed while inserting a wire making in hand terminations much easier. This connector...
thingiverse
Links to parts on eBay Wireless DMX Module Female Chassis mount DC Power connector USB to DC adapter cable (straight) USB to DC adapter cable (angled) M3x12 screws Assembly instructions First insert the DC power connector in the base part, and...
thingiverse
I decided to create this simple box to house a small usb to dmx converter that I bought off ebay...
thingiverse
The DMX-40 Transceiver by PreppComm has a color touch screen that is hard to see in bright sun. An important status is indicated by a red word changing to orange, which is hard to see in bright sun. This two part sun screen will block sun from...
thingiverse
a xlr/dmx tester that is made out of 2 parts the one with the battery and switch (this one) and the other end with the LEDS. when you want to check if a cable is good you connect both ends and turn it on. when te 2 leds light up it is working 100%...
prusaprinters
a xlr/dmx tester that is made out of 2 parts the one with the battery and switch (this one) and the other end with the LEDS. when you want to check if a cable is good you connect both ends and turn it on. when te 2 leds light up it is working 100%...
thingiverse
This is an enclosure for the Enttec Open DMX Interface. For this print you dont need a printer with dual extrusion, you first print out the lettering(the plate on top of the lettering is so smoul, that your printing software wont detect it), leave...
thingiverse
Customized version of https://www.thingiverse.com/thing:28405 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=28405