dnd dice set 3d models

The shield fits a set of 7 role playing dice. For the symbol on the front of the shield, either use the "Shield Symbol" part or the mirrored version. You don't need both. This is just based on which way you want the shield to face. This...

dice roller Print Settings Printer Brand: Creality Printer: CR10S PRORafts: No Supports: NoResolution: .2 Infill: 20 Filament: Hatchbox PLA, ABS, PETG any Category: Dice

This is a small travel box for one set of polyhedral dice. I tried to make it as small as I could. It fits my set of Chessix dice no problem. It uses four 6mm magnets.</p><p>The magnets can be glued in place or slipped into the print with a pause...

This is a small travel box for one set of polyhedral dice. I tried to make it as small as I could. It fits my set of Chessix dice no problem. It uses four 6mm magnets.The magnets can be glued in place or slipped into the print with a pause at:19.6mm...

Room for pens, a full dice set, and hopefully whatever else you may need. It even comes with a cool sword design on the lid that I totally didn't just use Tinkercad's premade sword model for. Made to fit 10mm magnets to hold the lid to the tray. The...

... version of this a few days ago and I wanted to make it a little more precise as that was my first design. ...This box was designed to hold a few sets of mini dice I have collected over time. ...magnet holes are 11x3.5 for cheap amazon 10x3 magnets

Should prevent problems where some users cant fit their dice into the holes. Print Settings Printer Brand: Prusa Printer: i3 MK2S Rafts: No Supports: Yes Resolution: 200 Infill: 15 Filament: Colorfabb PLA Rainbow, Gray, Glow in the Dark Category:...

... you play and what need in the current situation. You can print the Upper_Box without supports, the DnD letters can be done using bridging. ... *Last but not least, if you like the design, please consider a tip, I need some beers after this ;-)*

This hammer was designed to hold a set of 7 dice (d4, d6, d8, 2d10, d12, and d20). The dice are stored in a tray that screws into the handle. When you are ready to roll you can unscrew the hilt and slide out the dice. There is also some extra...

The D12 dice kept failing and the cogs would be left attached to the supports (resin printer) so I put it in 3dbuilder and recessed them a little.They seem to print ok now, only the 6 or 9 cog stuck this time but on the other prints as long as I was...

This dice guarantees a crit succes 1 every 4 rolls.Also breaks the damage of the dice.The numbers are in Comic Sans to make it extra cursed.

Here's round 3 of the dice storage collection! This hammer was designed to hold a set of 7 dice (d4, d6, d8, 2d10, d12, and d20). The dice are stored in a tray that screws into the handle. When you are ready to roll you can unscrew the hilt and slide...

You may customize them according to what you play and what need in the current situation.You can print the Upper_Box without supports, the DnD letters can be done using bridging.Last but not least, if you like the design, please consider a tip, I...

These holes are spaced out to fit a set of 7 dice - d20, d12, d10, d8, d6, d4, & percentile. The main body of the shield was split into two parts so that it could fit on my print bed. Each of these parts halves was printed using multimaterial, 3...

... game. ...if there are any issues whit the model please let me know. (pictures coming soon) Print Settings Printer Brand: Creality Printer: Ender 3 Rafts: No Supports: No Resolution: 200-300 Infill: 30 Filament: generic pla/petg any Category: DIY

I saw a dice chair on amazon an did not want to buy it so i just made one

A mini dice sword for D&D except not nearly as good as The Original Dice Sword. For mini dice. Three separate pieces - handle, blade, and sheath, to be combined/mixed if you want to change it up. ...Also a stick to combine the blade and handle.

These holes are spaced out to fit a set of 7 dice - d20, d12, d10, d8, d6, d4, &amp; percentile. The main body of the shield was split into two parts so that it could fit on my print bed. Each of these parts halves was printed using multimaterial, 3...

I crafted this box to seamlessly encase my polyhedral dice set for Dungeons & Dragons, drawing inspiration from Victorian flair and Martin guitar bridge designs. The symbol atop is a runic D, the first letter of my name. It demands support to...

Updated Version https://cults3d.com/en/3d-model/game/dicer-tower-upgraded A dice rolling tower. Text on the front says "The dice will decide your fate" in Latin because everything's cooler in Latin. ...Guaranteed to give you good rolls ;) I printed it...

The hole in the top of his head is 20mm which should fit most dice. If you have bigger dice, then scale it up! I put some scaling percentages you can use to change the hole size of the tower below. ... 110% = 22mm 120% = 24mm 140% = 28mm

This is a dice jail that I made for a teacher. ...I have not seen any other dice jail such as this, so here you go. ...I hope you all like it and don't be afraid to show me your dragon heads.

Simple dice rolling tray designed with sleek dice towers that add an air of sophistication to any gaming session. ...I enhanced the look by adding a touch of silver accents around the lettering, making it stand out beautifully against the smooth PLA...

I recently crafted a custom dice tower within Masterpiece VR. ...While some minor adjustments are still needed - specifically, flattening out the sides of its base - the overall structure appears to be solid and functional.

my players would always loose their dice so this is just an easy way for me to keep them in a box during the game. if there are any issues whit the model please let me know. ... (pictures coming soon)

Dice case for up to 12 standard size dice, mini figure, pencil and eraser. Two options for the top of the case, smooth or with the skill logo. Ignore "The Jimmer" on the one in the picture. ...The files included here are text free.Requires (8) 3mm...

... in Blender 3D 2.80 + Cycles (or Eevee) Using an HDR Environment Texture Image Which is NOT Provided in the Package! Sketchfab 3D Preview: https://sketchfab.com/3d-models/66-rpg-dd-dice-set-collection-uv-textured-308fcc547dec442992e4568c623d574e

Check out the shield I made, here: https://www.thingiverse.com/thing:4926642 Check out the hammer I made, here: https://www.thingiverse.com/thing:4960893 Update 8/11/21: Dice hole dimensions were adjusted to provide a better fit. "Sword Handle - No...

... be printed as one big “flower” using big table and 2 extruder printer. I have small table and desided also to make it printable for those who have only one extruder. Pls, insert DND flex part carefully. ... https://youtube.com/shorts/i7OtpbzkvBY

The design is supposed to resemble a spellbook and is able to serve as a dice vault and rolling area, personal minature storage, as well as a player character sheet holder on the back of the cover. A Test print is still required. The dimensions...