doinker 3d models

21 3d models found related to doinker.
Doinker Case
Doinker Case
thingiverse

Very simple, just something to protect your doinker and make it easier to store! Feel free to print and share any feedback to make the design better! ... Print Settings Printer Brand: Prusa ...

Doinker Mods
Doinker Mods
thingiverse

On the doinker it won't fit underneath the PCB, so I had to mount it on the bottom. The second mount is the camera mount, with 2mm spacers attached, and the hole moved so the wire from the camera doesn't come out directly on the mounting bolt. ...Hope...

Doinker Battery Strap
Doinker Battery Strap
thingiverse

My first attempt at 3D design. ... Doinker battery strap is 28mm x 28mm x 2mm with 20mm hole spacing.

Archery Doinker Stabilizer Endcap
Archery Doinker Stabilizer Endcap
thingiverse

To make my Bow setup look as good as possible I made some endcaps for my Doinker weights. ...Just a simple thing, but makes it look much cleaner :)

Doinker Lipo Mount
Doinker Lipo Mount
thingiverse

This plate installs under the Doinker and uses a 1/2" velcro battery strap to secure the lipo. I shortened one from a Blade 180 cfx heli. There is room for a 3/8" x 3/4" piece of hook velcro in the middle if you use velcro on your packs. The extra...

Doinker battery plate
Doinker battery plate
thingiverse

... ... Simple battery plate for your Doinker quad. Battery attaches with velcro only, no need for straps. Has been heavily crash tested with no battery ejections. Bolt on using M2 countersunk screws. You need to countersink holes after printing.

Doinker propeller cutter
Doinker propeller cutter
thingiverse

Doinker is an awesome little micro quad, but it uses 2535 propellers that are cut to size, to fit inside the ducts. Cutting propellers can be a hassle, and hard to get the cuts equal on all blades. Introducing the nailclipper-powered prop cutter! It...

Doinker camera mount (QX90 camera)
Doinker camera mount (QX90 camera)
thingiverse

Doinker camera mount for QX90 aio camera, 20 deg tilt. Sketchup file included. ... Print Settings Printer Brand: Deltaprintr Printer: ...

Doinker Furious 700tvl Camera Mount
Doinker Furious 700tvl Camera Mount
thingiverse

I created this to add the Furious 700tvl 1/4 Cmos Camera to the stack on the Doinker. Leave a comment and let me know how it works for you. ...How I Designed This Drawn in SketchUp

Easton Contour - Recessed Doinker Bushings
Easton Contour - Recessed Doinker Bushings
thingiverse

These are threaded bushings intended to go between the end of an Easton Contour stabilizer for archery, and a Doinker A-Bomb damper. Having the narrow end of the stabilizer digging into the damper always rubbed me the wrong way - it seems to cause...

Doinker - 82mm Inductrix-style Brushless Quad
Doinker - 82mm Inductrix-style Brushless Quad
thingiverse

https://www.thingiverse.com/thing:2531356 10/13/2016 Doinker v2.stl replaced the Doinker.stl. This version has improved durability on the motor to duct arms. 11/5/2016 Added a plate for a battery strap. Best to print in TPU and can mount underneath...

Doinker - Eachine ef01
Doinker - Eachine ef01
thingiverse

This thing was made with Tinkercad. ...Edit it online https://www.tinkercad.com/things/gHr1DMw1OqK

Doinker Prop Cutter v3
Doinker Prop Cutter v3
thingiverse

Inspired by http://www.thingiverse.com/thing:1797211, I wanted to make one without a motor. ...Print Settings Printer Brand: MakerBot Printer:...

Doinker Lipo Battery Mount
Doinker Lipo Battery Mount
thingiverse

Resolved issue with hollow object and holes not open on other end.

BetaFPV H01 camera holder for Doinker with Pico BLX
BetaFPV H01 camera holder for Doinker with Pico BLX
thingiverse

Camera holder for BetaFPV H01 (VM275T) when used with Pico BLX on the Doinker drone. Camera angle: 20° Material: ABS, PLA Additional: Requirements:Use a 3mm or narrower cable tie to secure camera in place. ... BetaFPV H01 (VM275T) FPV AIO Camera...

doinker innova mount with no antenna support
doinker innova mount with no antenna support
thingiverse

cut off the antenna support to make it easier to print with tpu Print Settings Printer Brand: FlashForge Printer: ...

doinker innova mount with no antenna support
doinker innova mount with no antenna support
prusaprinters

<p>cut off the antenna support to make it easier to print with tpu</p> <h3>Print Settings</h3> <p><strong>Printer Brand:</strong></p> <p>FlashForge</p> <p class="detail-setting printer"><strong>Printer: </strong> <div><p>FlashForge Creator...

AIO FPV Camera Mount for Whoop Quadcopter (20x20 holes, 20-35 degrees, stright/diagonal)
AIO FPV Camera Mount for Whoop Quadcopter (20x20 holes, 20-35 degrees, stright/diagonal)
thingiverse

This mount was designed for Doinker frame and Eachine AIO FPV 5.8G 25mW 48CH camera, but it should fit many other AIO cameras. There options with different orientations and angles. You should print it with some flexible filament like TPU or...

FX798T & Battery Strap mount for Snappy Micro Brushless Frame
FX798T & Battery Strap mount for Snappy Micro Brushless Frame
thingiverse

Both were modified from Doinker components serving the same purpose. The base of each part should line up with the contour of the opening where the electronics are mounted. I use M3 nylon screws/bolts to mount the plates and to get the camera plate...

ZiDrohne - tough quad - 100mm Brushless - fpv
ZiDrohne - tough quad - 100mm Brushless - fpv
thingiverse

I really liked the "Doinker v3" design, but I wanted a slightly bigger quad. I first tried the "100mm Whoop Frame" (https://www.thingiverse.com/thing:2531356) but the problem was that it broke very reasily with a hard landing: the 90° angles of the...

100mm Whoop Frame (Fusion 360 parameter driven)
100mm Whoop Frame (Fusion 360 parameter driven)
thingiverse

I printed and used the [Doinker](https://www.thingiverse.com/thing:1676674) by TheShortCrayon. Its a great frame, but found that I wanted to be able to customise the sizing in many ways. Unfortunately, as I use fusion 360, editing meshes is...