dongle holder case 3d models

... sort of push on Adapter to hold a Lightning to Usb a adapter and a small dac. ... The phone must be around 75.4mm by 10mm. The size for the adapter should be around 34mm by 11.5mm for the one in the middle and 20mm by 12mm for the holder on the side

USB-C Audio Dongle holder for travel or storage, magnetic lid to keep it shut and safe when in a bag. ...

The dongle holder in the original SpaceMouse casing design by Michaelmi782 did not work for me, unfortunately. Too loose and very fumbly to maneuver the dongle into the slot. I made my own holder to be tighter and go from the side, though that also...

Case for usb dongle (ESP8266 module) with a cooling hole

A well fitting case for covering the XBEE explorer dongle with XBEE pro with antenna module.

... of the 3DR radio case. ...I just modified the case to fit the CC2531 Zigbee dongle. One big thing to note is, not all dongles created equal and there are many variation of this dongle. ...If the dongle matches the pictures I posted, it should work.

This is a case for the VGA EDID dongle at https://www.pcbway.com/project/shareproject/VGA_EDID_Dongle.html You will need to print two of them, each of them covers half of the dongle. ... It is mounted by the screws on the female VGA connector of the...

Case for the Crazyradio 2.4Ghz nRF24LU1+ USB radio dongle with antenna: * https://www.amazon.com/Crazyradio-PA-2-4Ghz-dongle-antenna/dp/B00QBP5242/ Prints on MakerBot Replicator 2: * High Quality: 53 min * Standard Quality: 27 min

This case is made for a magic mouse and a dongle. The box is almost fully printable. You only need to add two bolts (M4x10mm). I will upload a fully printable one as well. ... Dongle type: Satechi Pro USB-C Thunderbolt

Wanted a case for the Xbee Explorer Dongle from Sparkfun: http://www.sparkfun.com/products/9819 So I made one. This thing was made with Tinkercad. ...Edit it online https://tinkercad.com/things/epx6ZUHNISU

Case for Stratux Softrf T-Motion Parts: - Stratux - Softrf T-Motion Dongle - Softrf Skyview ez - usb to serial converter - usb A board - usb micro board - capacitor 1000uf 6,3v - div. ...cables

Case for softrf Projekt https://github.com/lyusupov/SoftRF all rights by Linar Yusupov Version 1: Case for Skyview and dongle in one case with hole for audio jack New Version 2: - TP4056 micro usb lipo charger - micro 7x7mm switch - space for an...

... 360 and how to create a good print. The design features symmetrical half cases and has a thinned out section of material to allow the LED to be visible when it is on. ... It might be useful to someone who is designing a small dongle of their own.

Wanted a case for the Xbee Explorer Dongle from Sparkfun: http://www.sparkfun.com/products/9819 So I made one. This thing was made with Tinkercad. ...Edit it online https://tinkercad.com/things/epx6ZUHNISU ...

A box with a sliding top and access to a reset switch for the Centromere, Centromere Plus wireless dongle.

Holder for usb wifi dongle

Box for RTL-SDR dongle with some mods. Second SMA connector for direct sampling was added. ... Instructions Print to masking tape for nice top and bottom.

Alternative housing for Tundra 5/7 dongles to accommodate a heatsink 8x8x5 heatsink https://www.amazon.com/dp/B07YR6M6F6 USB card with 4 dedicated controllers https://www.amazon.com/gp/product/B00HJZEA2S

Read more at:https://bytechlab.com/2018/09/rtl-sdr-dongle-caseRecommended printing settings:Layer height: 0.1 mmHeated bed: 90 deg C or morePrinting speed: 40-60 mm/sFilament: ABS/ASAInfill: 25% (Grid) or moreOutlines: 2 or moreTop/Bottom 100%...

Case for the USBasp board (black) in two parts. The holes in the housing for the LEDs are sealed with transparent epoxy. The case is glued together and the programmer is inserted into the case. I also separated by cutting the conductive tracks from...

Slim case for the TI CC2531 USB Zigbee sniffer. ...Includes STEP and Fusion360 files for personal modifications.

The case is glued together and the programmer is inserted into the case. I also separated by cutting the conductive tracks from GND, and brought out the wires of the 5V - 3.3V switch jumper into two tracks (the cut points are marked with red...

This is a remix of the excellent CrazyRadio case by edauksis here: https://www.thingiverse.com/thing:3630927 Pins could be a little snug, just sand them down. Enjoy! ...

See full description of the project here : https://gitlab.com/jeroenmeijer/cansee/-/wikis/home This is 3D printed case which accomodates with cheap ODB2 connectors as this one :...

This is the case for the BlueRobin transceiver. ... Instructions Print both parts in PLA or ABS put the BlueRobin board in the box (first part) so that usb is sticking trough hole cover the box with the...

CAnSee is an ESP32 / Arduino firmware as a fast CANbus access gateway for the CanZE app. See full description of the project here : https://gitlab.com/jeroenmeijer/cansee/-/wikis/home This is 3D printed case which accomodates with cheap ODB2...

Single dongle holder that will securely hold 3 in place.

Casing to secure a Dongle/Mobile Router with a retro feel. ... Have fun

If you have some *really* low-profile USB dongles that fall out in the case, or if the rattling is a problem, you can add a bit of foam inside the lid after printing. ...There is deliberately a reasonable amount of space inside to allow for larger...

This holder has storage for 5x HDMI and 5x Displayport dongles/plugs.