door knob hole cover plate 3d models

This is a simple cap/cover for a standard door knob hole if you need to fill one (like if you removed a deadbolt lock). ...I used 25% infill, and glue it on.

This is a 4"x4" plate to cover a hole left after removing a broken door knob and latch from my basement door. I wanted to replace the knob, but, it turns out that the 60+ year old door is too narrow (1-1/4" wide) for store-bought, modern, door knobs...

door knob cover my Instagram

This part covers the hole in the door frame where the hinge used to be. After removing the door and then the remains of the hinge from the frame, this part can be slid in and screwed tight with the existing screw for the hinge. It covers the hole up...

Simple cover for a door ventillation hole, e.g for bathrooms. For each hole you'll need two, one for the inside, and another one for the outside of the door, but **that should be mirrored**! The minimum door width is 4cm, alternatively the model...

I tried my hand at creating a "cover" for the door hole. I wanted to close the hole , and decided to Sketch something in Fusion 360. Diameter of the circle is 70mm and its squared off to the dimensions of the original hole. For me it just fits...

This is a decorative plate to be attached to a door around the door knob. 

I took a panel off of 3DWP's lamp and used it to create a new door knob plate for my mortised door knob.

A plug to fit in the hole of our door knob covers to keep my 4-year old from pulling them apart lol. ... this has not yet been tested

Locking your door with a spare key? ...Tired of feeling the cold metal? Get comfortable with this..key knob cover thingi ...here.

Door knob from Alice in Wonderland for my granddaughter's playhouse.

... own. I initially search thingiverse and found nothing. I search with wrong keyword. Since I am french I did not have the proper way to describe this door knob cover. here it is, it use M3 nuts and you need to print 2 of them. ... Good luck!

This is just the plate/cover for the doorknob made by charliepsycho here: https://www.thingiverse.com/thing:1133271

Made furniture hole cover plate with the power cord. ...It is 3 different types of the same cover plate: - without a hole - without a hole with mounting holes - with a "U" shape hole for power cord

Place it over door knobs to prevent pesky muggles from entering places that they are not supposed to. Good for doors that you don’t have keys to (e.g. rental or lost keys). Provides adequate protection up to muggles without hammer, saw or really...

I cut some holes in a built-in closet I made but then realized that cover plates of this size are very difficult to find. The cover plate is friction fit. ...I printed it in PLA and it came out beautifully.&nbsp;</p>

Prevent your kids from opening doors. Quality: 0.2mm Infill: 15% or up ** I made it so no support is needed, might need a Brim for model 2. ...

door lock cover plate- inside and outside

Plug that hole ment for a dead-bolt. ... Very simple design but came in so handy for those holes that need to be sealed.

Space helmet door knob cover for children.  Print Settings Printer: XYZ Davinci Junior 1.0 Filament: ABS plastic Extruder Temperature: 213 °C Heat Bed Temperature: 90 °C Estimated Time: 2 hours Printed with supports: Yes Assembly  Attach both sides...

This door knob is printed in 2 parts and screwed together through the hole in the enclsoure door. ### Enclosure Door ### I would also recommend gluing strong magnets to the enclosure door exterior and the enclosure interior wall so the door stays...

We told the contractor that we would be installing dummy knobs/levers on the outside of the door only, so we would not need holes cut for regular door knobs. BUT, he proceeded to cut the holes anyways! ...So two of these little jobbers and we had a way...

Door handle safety cover to keep kids out of your printer room. Print with the small opening down and no supports. Included is also my gcode for the Tevo Tarantula printed at .12 layer height. You will need to print two per door. ... Be advised I...

Cover for the hole in the bottom of your Ivan's U-Bolt trigger hole. ...Should just snap into plate with a little bit of force, but you can glue it if you prefer.

To keep your kids out of rooms you don't want them in. ... This is 1/2 of the cover, just make a copy and print so you'll have 1 complete cover.

The definitions are at the beginning of the file and I provided comments as to what each parameter does so that you can easily change it to match your needs: blindhole=75; //Diameter of the blind hole to cover holedepth=12; //Depth of the hole,...

Designed to fill in a hole where a spotlight had been previously installed. One version allows for a cable to go through. ...Print Settings Printer: Wanhao Duplicator 4S ...

... below! ... Das ist eine Abdeckung für das Loch im IKEA ALEX-Schrank mit Tür (601.928.26). Für alle die das Loch nicht benötigen... Its a cover for the hole in the IKEA-ALEX-cabinet with door (601.928.26). ...For all who don't need this hole...

Removed the door latch from the pantry door and replaced the gap with this blanking plate. One size should fit all. ...

Instead of closing up the hole with drywall and putty I thought it might be useful to have a removable door which will make life easier in the future to service the conduit or wires. I hope this makes someones life easier or perhaps it will come in...