double switch plate one side blank 3d models

I created this wall plate to be used for a standard double box with only 1 switch installed. Customized version of http://www.thingiverse.com/thing:47956 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=47956 Print...

http://www.thingiverse.com/apps/customizer/run?thing_id=47956 Instructions Using the following options: plate_width = 2 5th_plate = none 2nd_plate_bottom_hole = none 2nd_plate = none 4th_plate = none 1st_plate = toggle plate_size = 0...

This plate was designed to replace the previous plate which was a standard double switch plate, with duct tape holding the left side down because I changed the overhead from a light/fan to just a light. ...It's a short term solution until we have an...

Just a Double blank wall plate

http://www.thingiverse.com/apps/customizer/run?thing_id=47956 Instructions Using the following options: 5th_plate_bottom_hole = none 5th_plate = none 3rd_plate_bottom_hole = none 4th_plate = none 1st_plate_bottom_hole = none 2nd_plate_bottom_hole =...

http://www.thingiverse.com/apps/customizer/run?thing_id=47956 Instructions Using the following options: 5th_plate_bottom_hole = none 3rd_plate = none 3rd_plate_bottom_hole = none 1st_plate = none 5th_plate = none plate_width = 2 4th_plate = none...

Yep, if you're too lazy (or too far away) to drive to the hardware store or big box home improvement store but stupid enough to spend way more time designing (or, in your case, searching for and then downloading and slicing) a wall switch plate blank...

This is a completely blank double light-switch cover. ...It is a perfect fit for standard American light-switches.

Customized version of https://www.thingiverse.com/thing:47956 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=47956

I wanted to put a use to the existing blank plate in my room, so I decided to whip this up to make an easy key rack. I could have just downloaded someone else's, but I didn't see a lot of them on this site. ...

http://www.thingiverse.com/apps/customizer/run?thing_id=47956 Instructions Using the following options: 4th_plate = none plate_width = 1 1st_plate_bottom_hole = none 5th_plate_bottom_hole = none 2nd_plate_bottom_hole = none 5th_plate = none 3rd_plate...

http://www.thingiverse.com/apps/customizer/run?thing_id=47956 Instructions Using the following options: 2nd_plate_bottom_hole = none plate_width = 2 3rd_plate = none 1st_plate_bottom_hole = none 2nd_plate = none 4th_plate_bottom_hole = none 4th_plate...

I have the one that is a remix, then the one without holes that I built in tinkercad More pics / details here: https://www.printerknowledge.com/threads/3d-print-project-2-gang-wall-plate-with-blank.12524/ Customized version of...

Double switch plate for a child's room.

http://www.thingiverse.com/apps/customizer/run?thing_id=47956 Instructions Using the following options: plate_size = 0 3rd_plate = none 4th_plate = none plate_width = 1 2nd_plate_bottom_hole = none 5th_plate_bottom_hole = none 4th_plate_bottom_hole =...

Instructions Using the following options: 3rd_plate = none 4th_plate_bottom_hole = none 2nd_plate_bottom_hole = none 5th_plate_bottom_hole = none 5th_plate = none 2nd_plate = toggle 1st_plate = blank plate_width = 2 3rd_plate_bottom_hole = none...

Customized version of https://www.thingiverse.com/thing:47956 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=47956

Instead of buying a new 3 gang plate with just 1 switch hole and the rest solid to clean it up, I decided to keep the plate and design a blank that would secure the plate and fill the empty switch hole. I made a few versions and the one I like the...

This a double gang switch plate with two roses which I painted with acrylic paint. I printed it in white PLA with supports at 3% touching buildplate only. ...

servo plate size 23*12*29 2 momentary switches, the arm of the servo operates the switch ideal release of electromagnet light trap etc

For your home/office, here is a common style switch wall plate with two switch positions incorporated. These switches types are typically mains powered and intended for switch lighting control. The power switch is designed to press fit into...

For your home/office, here is a common style switch wall plate with two switch positions incorporated. These switches types are typically mains powered and intended for switch lighting control. The power switch is designed to press fit into...

For your home/office, here is a common style switch wall plate with two switch positions incorporated.  These switches types are typically mains powered and intended for switch lighting control.  The power switch is designed to press fit...

http://www.thingiverse.com/apps/customizer/run?thing_id=47956 Instructions Using the following options: 3rd_plate = none 4th_plate = none 1st_plate_bottom_hole = none 3rd_plate_bottom_hole = none 1st_plate = toggle 2nd_plate_bottom_hole = none...

http://www.thingiverse.com/apps/customizer/run?thing_id=47956 Instructions Using the following options: 5th_plate = none 3rd_plate = none 1st_plate_bottom_hole = cat5e 4th_plate_bottom_hole = none 2nd_plate = cat5e 3rd_plate_bottom_hole = none...

http://www.thingiverse.com/apps/customizer/run?thing_id=47956 Instructions Using the following options: 2nd_plate = toggle plate_size = 0 1st_plate_bottom_hole = none plate_width = 2 3rd_plate_bottom_hole = none 2nd_plate_bottom_hole = none 1st_plate...

http://www.thingiverse.com/apps/customizer/run?thing_id=47956 Instructions Using the following options: 1st_plate = toggle 3rd_plate_bottom_hole = none 5th_plate_bottom_hole = none 4th_plate = none 2nd_plate = blank 1st_plate_bottom_hole = none...

Mitsubishi dashboard switch blanking plate 47mm wide x 20mm high. It fits my 1997 Delica but will likely fit many other models, e.g. ...Pajero, Triton, etc.

This is a Remix of the Toyota Blank Dash Plate - (https://www.thingiverse.com/thing:1198435) modified for use with a CH 5588 4 pole Switch and 5 amp circuit breaker for uses in a Scion TC dash insert.

I could not find an STL for this popular light switch plate...so I made a quick one in TinkerCad