dowel holder 3d models
327057 3d models found related to dowel holder.
thingiverse
Mountable dowel holder (with and without "latch") for a sliding door. I have kids who play with the dowel if it's on the ground-level. ... I made these to hold the dowel up high and out of their reach.
thingiverse
A small holder for, in my case a cut off broomstick, but any type of 25 mm dowel
cults3d
A small holder for, in my case a cut off broomstick, but any type of 25 mm dowel
thingiverse
A cup and ring for storing dowel rod or other long, thin material on your studio wall.
pinshape
Sea Turtle dowel holder that fits a 5/8in dowel. ...3 holes for screwing directly into the wall.
thingiverse
16mm dowel holder with countersink. Good to add a dowel to the front of a shelf to stop jars falling off. ... Dowel rod clicks into place.
thingiverse
This dowel holder is designed to hold a 1/4" dowel. ...Print two and it should fit snugly into your IKEA Skadis
thingiverse
Customized version of https://www.thingiverse.com/thing:2931530 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=2931530
thingiverse
A simple marble track holder for a 3/8 wooden dowel. It has a vertical piece along with four side slots to attach multiple holders together. It also has four small holes for mounting screws. This is is meant for my DIY Olympic track set which can...
thingiverse
This is a simple curtain rod holder, designed to drop a rod or dowel in from the top. There is a single screw hole in the base to attach it to the wall. Mom is a pre-K teacher and has a few curtains in front of some storage areas in her classroom....
thingiverse
I designed this part to use in a Ikea Billy bookcase, It's designed for a 22mm (dowel)rod and the mounting holes are spaced for the plank peg holes. ... Offcourse is this part also useable for for any other inside dowel mounting application.
thingiverse
Dowel Holder for 1.25" or 32mm diameter doweling. I used this to create feet for a monitor riser. ...The holder screws to a flat board and the doweling slips in.
thingiverse
Used Two 1/2" Dowel holders to make a towel holder in kitchen sink cabinet with a few small screws. Very sturdy in all aspect. ...Spray painted dowel black and used scotchbrite for a smoother, matte finish
thingiverse
Wooden dowel holder designed to hold spools of filament in my plastic totes. It could be used for a variety of different projects. I converted the dimensions from inches to millimeters so that it would scale properly. ...The base is one square inch and...
thingiverse
Based on http://www.thingiverse.com/thing:961881 however I decided to use a 1 1/4" Dowel instead
thingiverse
I designed this to hold a 5/8" (0.625") dowel or rod for curtains. I made two versions: bolt-on (hole and hex recess for #8 nut), screw-on (countersunk hole for #8 construction or drywall screw). ... This can be printed without supports.
thingiverse
... hanging of the clothes prevented the door from closing. ...I opted to mirror & flip the print to minimize swigging, but this doesn't appear to be necessary. Print this twice & purchase a 7/8th dowel from the home store - it will be a perfect fit.
thingiverse
simple 1/2 inch dowel rod holder Print Settings Printer Brand: Robo 3D Printer: R1 ABS + PLA Model Rafts: No Supports: No Resolution: Default Infill: 25% Notes: Make sure you scale it up x10 in your software before printing
thingiverse
This thing was made with Tinkercad. ...Edit it online https://www.tinkercad.com/things/3Hgr1cfqV85
thingiverse
This thing was made with Tinkercad. ...Edit it online https://www.tinkercad.com/things/kFxkE3d9gEX
thingiverse
This thing was made with Tinkercad. ...Edit it online https://www.tinkercad.com/things/3Hgr1cfqV85
thingiverse
This thing was made with Tinkercad. ...Edit it online https://www.tinkercad.com/things/3Hgr1cfqV85
thingiverse
This thing was made with Tinkercad. ...Edit it online https://www.tinkercad.com/things/3Hgr1cfqV85
thingiverse
This thing was made with Tinkercad. ...Edit it online https://www.tinkercad.com/things/3Hgr1cfqV85
thingiverse
A customizable dowel holder for use in making filament dry boxes, filament spool racks, stands with racks for the Mosaic Palette+, etc. I've included 2 premade stls. The "-dry-box" I used to make a filament dry box to hold nylon / pva and it...