dowel rod connectors 3d models

A bunch of dowel rod connectors for 3/8" dowels

This object was made in Tinkercad. ...Edit it online https://www.tinkercad.com/things/cp81NY5PgDO

A set of connectors to use with 1/4 inch diameter wood dowels.

Customized version of http://www.thingiverse.com/thing:1122034 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=1122034 Instructions Using the following options: Wall_Thickness = .75 Rod_Depth = 4 Rod_Diameter = 1.91

Simple connectors to make a frame for a tent out of dowel. All parts with printed without supports at .2mm layer heights. Designed to fit on a Ikea HEMNES bed frame using no screws and leaving no marks. ... You can either have a flat roof or a...

Uses 5/8th dowel rods. 

simple curtain end, uses a 1/2 inch dowel as the rod.

Printable dowel rod for shelving slots. ...5mm diameter/20mm length with beveled edges.

Small mount for a 10mm dowel rail. ...Longer runs can be supported with this - https://www.printables.com/model/217946-10mm-dowel-rod-mount-centre-support 

... 2 for symmetry. The extender is a total of 4.5" long with a 1" hollow core on the larger end to insert the dowel rod. If 1" is too much, just mark where you need the dowel rod to sit, and stuff with a bit of paper towel and compact until it's tight.

Support me on Patreon! ... https://patreon.com/user?u=9536492&utm_medium=social&utm_source=twitter&utm_campaign=creatorshare2 For use with 5/16 dowel rods, or remix for custom dowel size.

A simple dowel rod that you can 3d print in about 30 minutes per rod for the Washi Tape Dispenser by ermosher (thing:2813821). ...It has a 3m deep hole for piloting the screw to help assembly.

simple 1/2 inch dowel rod holder Print Settings Printer Brand: Robo 3D Printer: R1 ABS + PLA Model Rafts: No Supports: No Resolution: Default Infill: 25% Notes: Make sure you scale it up x10 in your software before printing

This tool has holes cut for each size of dowel rod you'll likely use in cosplay. ...It allows you to test varying wall thicknesses to ensure a consistent fit.

This is a simple curtain rod holder, designed to drop a rod or dowel in from the top. There is a single screw hole in the base to attach it to the wall. Mom is a pre-K teacher and has a few curtains in front of some storage areas in her classroom....

Drape a tarp or shower curtain over the frame and you've got a quick, low cost, customizable temporary enclosure for messy activities like painting or sanding, or containing 3D printer heat and fumes.These brackets were sized for 5/16" dowel rods but...

A basic rundown: Rod_diameter: The exact size of your dowel. The script adds in 3mm of play. holder_protrusion: The amount of distance the "U" protrudes from the face of the base b_height: If you'd like a taller base to give you more 'gripping' area...

These 8020 Dowel Rod Hangers are used to hang wire for organization and dispensing.Hardware Required:1 x 3/8" or ½" Tubing or Dowel RodPrint BOM:2 x 8020 Dowel Rod Hangers of the same size as your extrusionsPrint Parameters:Material: PLA, PETG, ABS,...

I made these to fit a ¼ (.25) inch dowel rod from the hardware store that can be picked up for $1.25 in lengths of 4 feet. Holes were made to size, but it takes the rods snugly when printed at .2mm layer heights. Edges are nicely chamfered, and it...

The uploaded STLs can be used with four 3/8in dowel rods. (which set me back $6.05 so easily the cheapest shelf i've ever installed) NOTE: still working on getting the thread settings right to find the sweet spot of print-ability and strength EDIT:...

Simple 1" replacement dowel rod wall mounts. ...1/4" center through hole for mounting.

Closet rod type holders for common dowel sizes. Print one each open and closed. ...the "all Dowel holders file prints one of each in all sizes

... panels and other things. ... uses 11mm dowel rods and 8mm dowels. ... **Full Instructions** This is part of an instructable called ONE PERSON SOLAR PANEL INSTALLATION KIT https://www.instructables.com/id/One-Person-Solar-Panel-Installation-Kit/

Pushed onto the end of a 0.30"-diameter dowel rod after adhesive dried. ... And a friendly reminder that this uses a certain company's intellectual property in it's design so please don’t p*ss The Mouse off trying to make any money off of this...

A lot of spool holders and other designs often call for a 1" dowel rod. I don't keep those readily on hand, but I have a 3D printer! Ain't nobody got time to go to a hardware store. I couldn't easily find a 1" printable rod here on Thingiverse, so...

Simple storage for all the threaded rods, bars, dowels, and misc long-thin items I use for models/modeling. The base and middle "support" are printed, along with a lifting disc for each tube. The tubes are just old-school fluorescent T12 tube guards,...

I designed this to hold a 5/8" (0.625") dowel or rod for curtains. I made two versions: bolt-on (hole and hex recess for #8 nut), screw-on (countersunk hole for #8 construction or drywall screw). ... This can be printed without supports.

For the back piece, I used a small curtain rod holder made by 3Dsection (thing:2614484) because it had a slot that made it easier to slide the dowel inside of it and load the rolls of filament into the bin. Cheers for making a super useful design! ...

After that measure the distance between supports and buy 1 inch dowel rod  then just drop them into the brackets make sure you account for the length you have made your shelf and add middle supports as necessary.I hope you like this project as...

Dowel hanger bracket for 3/4 dowels. Use them to make racks for spare reels in the bottom of my cabinet. Dowels once cut to length snap into the brackets. ...