dowel rod holder 3d models
385602 3d models found related to dowel rod holder.thingiverse
simple 1/2 inch dowel rod holder Print Settings Printer Brand: Robo 3D Printer: R1 ABS + PLA Model Rafts: No Supports: No Resolution: Default Infill: 25% Notes: Make sure you scale it up x10 in your software before printing
thingiverse
Part of a design for my filament holder, it's just a simple block that can be modified to hold different sizes of dowels. Play around with the settings in the scad file to figure out how they respond. A basic rundown: Rod_diameter: The exact size...
thingiverse
For the back piece, I used a small curtain rod holder made by 3Dsection (thing:2614484) because it had a slot that made it easier to slide the dowel inside of it and load the rolls of filament into the bin. Cheers for making a super useful design! ...
thingiverse
I remixed this to be a friction fit hole for 5/8 dowel rods. You can easily sand it to make the dowel slide through the hole to fit your needs. Idabkey's orginal printing instructions work great: "Settings (Suggested) Raft: On Supports: On Infill:...
youmagine
When looking for a rod holder for a filament hanging solution based around http://thingiverse.com/thing:240760 I didn't find one that I liked. 2 screws holding them in place? Why? So I made my own, but it was a bit boring, so I decorated it with...
thingiverse
When looking for a rod holder for a filament hanging solution based around /thing:240760 I didn't find one that I liked. 2 screws holding them in place? why? So I made my own, but it was a bit boring, so I decorated it with gears and things. Why, not...
thingiverse
I'm using a 19mm, 3/4in. ...rod to hang stuff on my wall. These are the mounts I made to use with adhesive tape. The slot for the rod has an extra mm of tolerance, it's 20mm in diameter.
prusaprinters
This holder was built with a ¼" screw shank hole to accommodate the the Hillman's Wall Dog 1-1/2 in. ...Hi-Lo Steel Pan-Head Philips Anchors which are found on <a href="https://a.co/d/bIWjiGY">Amazon </a>and at hardware stores like <a...
thingiverse
Closet rod type holders for common dowel sizes. Print one each open and closed. ...the "all Dowel holders file prints one of each in all sizes
prusaprinters
This holder was built with a ¼" screw shank hole to accommodate the the Hillman's Wall Dog 1-1/2 in. ...Hi-Lo Steel Pan-Head Philips Anchors which are found on <a href="https://a.co/d/bIWjiGY">Amazon </a>and at hardware stores like <a...
thingiverse
This is a simple curtain rod holder, designed to drop a rod or dowel in from the top. There is a single screw hole in the base to attach it to the wall. Mom is a pre-K teacher and has a few curtains in front of some storage areas in her classroom....
thingiverse
I designed this to hold a 5/8" (0.625") dowel or rod for curtains. I made two versions: bolt-on (hole and hex recess for #8 nut), screw-on (countersunk hole for #8 construction or drywall screw). ... This can be printed without supports.
thingiverse
Customized version of https://www.thingiverse.com/thing:4758695 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=4758695
thingiverse
Customized version of https://www.thingiverse.com/thing:4758695 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=4758695
thingiverse
Customized version of https://www.thingiverse.com/thing:4758695 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=4758695
thingiverse
Customized version of https://www.thingiverse.com/thing:4758695 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=4758695
thingiverse
Customized version of https://www.thingiverse.com/thing:4758695 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=4758695
thingiverse
Customized version of https://www.thingiverse.com/thing:4758695 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=4758695
thingiverse
just a simple helmet holder using a 7/16 dowel rod you can cut to any length
thingiverse
An adaptor to fit a common rod holder provided on some fishing boats. ...Useful to mount a smaller common type of fishfinder in the bow or gunnel.
thingiverse
A teacher needed to put a battery operated LED tealight onto the end of a long 3/8" dowel rod. Since this is for small children glue or tape would not survive long enough to practice and actually still have them for three days of a show. The needs...
thingiverse
Designed in tinkercad as others were too small for my use and broke with rough handling. ... Made to be used with a 3/8" dowel or a stick from shore. ...Printed in different colors so the kids could tells them apart.
thingiverse
A sphere shaped curtain rod holder for 1/2 Inch wood dowels. About 1-7/16 inch (36mm) in outer diameter. Mount with #6 pan head screws or strong double sided tape. ...
thingiverse
A close-to-the-wall mount curtain rod holder for 7/16 inch (11mm) metal rods or wood dowels. The snug fitting clip uses arm tension to grip a wood dowel in place. Holes for #6 pan head screws--the ones in the picture are Spax #6, 5/8 inch length. ...
thingiverse
Once complete, slide the fitting over a 5/8 " Dowel rod of whatever length you need. Poke it in the ground and you'll have a self standing monopod type thingy. I also added a pre sliced version with support. ...Generated from Simplify3D Note: Added...
thingiverse
Customized version of http://www.thingiverse.com/thing:731318 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=731318
thingiverse
This is a prototype for a clip-on dowel rod holder. Print two, clip inside the bird cage on opposite sides, and insert the dowel between them to create a roosting spot / perch. ...There are holes in the clip so that wire can be run through them to...
thingiverse
Simple dowel rod holder for a 19mm or 3/4" dowel rod. It should be a slightly tight fit so that the rod snaps into the hook / holder. Use standard sheet rock screws but find a stud! ... don't over tighten or you will break the plastic