drawstring clip 3d models

Human: Customized Version of Thingiverse's Model 94018 Created with the Customizer App on Thingiverse www.thingiverse.com/apps/customizer/run?thing_id=94018 Using These Options: • clip_thick is Set to 3 • offset is 0 • clip_tooth_spacing is 6 •...

also known as a U clip, rod clip, cylinder clip, bar clip, circular clip, pipe clip, etc Was created for a 40oz hydro flask water bottle. Values for this application: r = 45.466 t = 6 opening = 110 h = 30 printed in PLA with 30% tetrahedral...

https://www.thingiverse.com/apps/customizer/run?thing_id=94018 Using the following settings: • Clip to tooth size: Medium • Clip width: Thick at 9 units • Clip back length: Standard at 45 units • Text: • Font: Black Rose - write/BlackRose.dxf •...

This Belt Clip will work with ICOM original Belt Clip Adapter or with my Belt Clip Adapter that i have designed ( ICOM Belt Clip Adapter )Infill: 30-40%Printing Position : On the side for maximum strength (see picture)The only bad thing: support is...

http://www.sodnpoo.com/posts.xml/ parametric_pole_cable_clip.xml pole_dia - diameter_of_the_pole pole_thickness - circular_area_around_pole( 3mm ) pole_height - overall_height_of_print (5mm) clip_thickness - thickness_of_clipped_area_part(2mm )...

This Belt Clip will work with ICOM original Belt Clip Adapter or with my Belt Clip Adapter that i have designed ( ICOM Belt Clip Adapter )Infill: 30-40%Printing Position : On the side for maximum strength (see picture)The only bad thing: support is...

The double clip design is not mine and I have remixed the single clip based on the original design. I could not locate the thingiverse page for this clip so I could not mention them. The single clip design is to go with my Pi Cam mount for Ender 5....

I designed some simple TPU clip retainers for my son's Traxxas Rustler RC truck (dual front clips, single rear clip, and a retainer for each clip on the battery bar). However, these leashes should work fine in any RC clip situation. ... Simple design,...

I've combined the 2 clip designs to make my own version I like the spool clip on this design: https://www.thingiverse.com/thing:3443881 And I like the filament clip on this design: https://www.thingiverse.com/thing:2364133 It now clips very tight and...

http://www.thingiverse.com/apps/customizer/run?thing_id=94018 Instructions Using the following options: height = 5 inches clip_front_length = 65 mm clip_thick = 4 mils clip_height = 9 inches offset = -2 degrees clip_back_length = 50 millimeters font...

Rear clip that attaches to the chassis using the 2 pin style clips This is the rear clip that comes on the Red chassis (short wheel base), this has been recreated so that you can use the red body style clip on the yellow chassis (long wheel base) or...

... the tab slightly and added a 3mm hole. ...As illustrated in photo, use a paper clip to remove and reinstall clips. No more clips flying out of your fingers and vanishing! ...The paper clip can also be used to store your extra bowden tubing clips.

... a snap! ...The Voronoi Clip is here for all your clipping needs. Simply clip it on your favorite item, and you're ready to go. Featuring sub-15 minute print times, the Voronoi clip is extremely fast to print and requires no assembly.   

This is a replacement clip for my sandwich toaster, because the original clip broke. The new clip is much stronger, than the old one. I printed the clip in PLA, because I believe, that the heat will not get to the clip. I will update here, if I am...

Fenders Arrived with One Clip, But After Trimming Front Fender to Fit Fork, Additional Support Was Needed Above the Section That Clips onto the Fender. Width of Section That Actually Clips onto Fender Appears Slightly Tight, but Still Snaps into...

I love the Socket Clip but found that the clip could easily break. ...So I redesigned the clip base in two pieces so that it prints in a more “compliant mechanism” friendly way.

This is a remix from https://www.thingiverse.com/thing:3350434 Cable pipe clip for stack mount. A 4,5mm Screw can be used to fix the clip. ...35mm of the screw disappears in the clip.

Replacement Latch clip for the Elna Lotus, at some point the original plastic clip was lost, this clip replaces it and allows the side panel to be latched closed.

35mm DIN Rail clip to attach to anything that needs a clip. ...Distance is set to 34mm so that when attached there is a slight spring force holding the clip in place.

a different version of my chip clip. ...this chip clip 2, was made in a cad program. and is thinner. my original chip clip was made in a modeling program. Category: Kitchen & Dining

Simple Clips are designed to be screwed into the wall and hold curtains in place. ... Inner diameters: 45mm (curtain clip) and 33mm (mini curtain clip) A screw hole is provided for countersunk screws, with a through hole of 4.5mm.

A body clip based clip mostly used in RC cars to fasten the body to the frame. ...The part is based on measurements of one of my own clips.

This is a clip designed for the iCraze or similar Laptop Desk Stand - Adjustable Laptop Holder. ...The clip goes over the edge lip and is similar to the clip which ships with it. ...

Remix of the clip itself. ...The provided clip only works on the Elite Strap, this clip will hold the stock strap in place as you feed the stock strap into it.

This is a sun visor clip to replace the factory rubber clip. I own two MG Midgets and both sets of rubber clips failed. ...Works on Austin Healy and Triumphs as well.

These clips are for a SAMSUNG fridge soda/produce drawer. ... These clips hold the sliding divider in place so they don't shift when opening/closing. The clips snap into the vent openings. ... Useful Crap #013

A basic clip for creating a balloon arch. ...Can be used with 10mm diameter flexible poles from a dome tent. Usage instructions: thread the clips around the tent poles and attach four balloons to each clip.

Here is my design for the pacifier clip, a do-it-yourself project that utilizes a salvaged spring from a clothespin or clothes peg. ...To assemble the clip, attach the spring to the body of the elephant-shaped clip.

This flat clip substitutes the circular clips provided with your printer. It features a 0.25mm space for the screw at its join, which can be separated post-printing using a fingernail. ...In total, you require three of these clips.

this body clip holder is placed by drilling a small hole in the middle. ... and make a wire running from one clip to the other, never loose your pins or clips again, when you are bashing in the park.