drill bit sharpener 3d models

This drill bit features a diameter of 7.5mm, a pitch of 67, and a length of 100mm. ...Its point angle measures 60 degrees, while it has a 1mm chamfer at the top.

This is a spool winder drill bit for the little embroidery thread card spools. ... I printed mine with a layer height of 0.2 mm and a Gyroid fill pattern and 50% fill density.

The customized version of this design can be found at http://www.thingiverse.com/thing:91035, created using the Customizer app with the specifications set as follows: Resolution = 25; Set Screw Nut Diameter = 5.5; Set Screw Nut Thickness = 3; Drill...

Key features of this version include a drill bit length of 20mm, a resolution of 25, a set screw nut diameter of 5.5mm, a set screw nut thickness of 3mm, a drill bit diameter of 4mm, two nut traps, a handle length of 65mm, a set screw diameter of...

Specifications include a 20mm drill bit length, 25mm resolution, and drill bit diameter in millimeters. ...Other specifications are a set screw nut diameter of 5.5mm, thickness of 3mm, a 3mm set screw diameter, 15mm handle diameter, 65mm handle length,...

The carousel is designed to be easily removed from its holder if you need all the drill bits somewhere else. Have fun making, do you like it? LIKE it! #BREAKING! **Madc** created a magical version of the carousel that can be tailored made by...

... of the holder. To optimize performance, one can flip the holder upside down and align the drill bits to the bottom, which will be the front face of the holder after printing. ...This alteration might expedite printing and reduce material usage.

The customization options include a drill bit diameter of 4.5 units, two nut traps, a handle length of 65, a handle diameter of 15, a set screw nut diameter of 5.5, a set screw diameter of 3, a resolution of 50, and specific thicknesses and lengths...

The customization includes a handle diameter of 15mm, drill bit diameter in inches, two nut traps, a set screw diameter of 3mm, a set screw nut diameter of 5.5mm, a resolution of 25, a set screw nut thickness of 3mm, a handle length of 65mm, and a...

I have an Ozito power exchange cordless drill and wanted a bit holder. Inspired by this https://www.thingiverse.com/thing:3302085 I made a remix so that I will fit my Ozito cordless drill. Mine uses magnets to hold the bits, since I only have 8mm...

Instructions Using the following settings: * Set Screw Nut Thickness set to 3 * Handle Length adjusted to 65 mm * Handle Diameter increased to 15 mm * Set Screw Nut Diameter enlarged to 5.5 mm * Drill Bit Length extended to 20 mm * Resolution...

To learn more about the scanning process and access a printable 3D Scanner design, visit: https://www.thingiverse.com/thing:2755968 This drill bit could serve as an engaging kids' toy or educational model, providing valuable hands-on learning...

The specifications include a Resolution of 50, Set Screw & Nut Diameter of 5.5, Nut Thickness of 3, Drill Bit Diameter of 3.5 (unit: mm), Handle Length of 65, Drill Bit Length of 22, Number of Nut Traps set to 2, Set Screw Diameter of 3, and Handle...

http://www.thingiverse.com/apps/customizer/run?thing_id=91035 Instructions Using the following settings: Drill Bit Diameter Units: inches (1) Drill Bit Length: 20 mm Resolution: 0.1 degrees Set Screw Nut Thickness: 3.18 mm Handle Diameter: 15.24 mm...

To create this, settings such as screw-nut diameter (5.5), resolution (25), screw-nut thickness (3), handle length (65), drill bit diameter (7), handle diameter (15), and number of nut traps (2) were applied. ...The drill bit length was set at 20 for...

Created with Customizer at http://www.thingiverse.com/apps/customizer/run?thing_id=91035 Options Used: Handle Length: 65 mm Drill Bit Length: 20 mm Handle Diameter: 15 mm Number of Nut Traps: 2 Drill Bit Diameter: 4 mm (unit: inches) Resolution: 25...

This is single long magnetic bit holder for the side of my Porter Cable Drill. The magnet is glued in the part and then the part was glued onto my drill. ... Affiliate Links: Ender 3https://amzn.to/3pxdoy8 Filamenthttps://amzn.to/3KfopMn Magnets 6mm X...

I'm using this with my Ridgid Impact Drill X4 (R86034). ...Needing a longer screw than the original, an M4x8mm will do. In the photo you'll see I've attached a magnet to the bottom to prevent bits from falling when the drill is turned upside down.

... fits on my pegboard. ...This specialized holder is specifically designed with my drill bits in mind, ensuring they are securely stored and easily accessible when needed. ...If you require any additional details about this project, feel free to ask.

Workers prepare for drilling by printing a layout, attaching it to a pegboard, loading drill bits into it, and getting ready to go.\r\nThe pegboard holes used at Biltema measure 4 millimeters in width and 12 millimeters apart from each other,...

... that fits perfectly onto 16mm diameter holes. ...To achieve precise results, they insert small washers into the countersink before attaching it to the drill press or hand drill, allowing for easy adjustment of the desired depth in each material hole.

It is not attached to the drill machine, but can be held by hand or clamped to the drill/stand. I used two 626 bearings (19 mm wide, 6 mm hole) and inserted them during printing (two times to set the printer to pause). I think these two bearings...

To get started, adjust the settings as follows: - Length of the drill bit: 30mm - Resolution level: high definition at 25 microns - Diameter of the set screw nut: 5.5mm - Thickness of the set screw nut: a robust 3mm for added strength and security -...

I crafted a versatile bit holder for my drill driver, constantly navigating cramped attics and crawl spaces with ease. Designing this accessory was inspired by Scarou's ingenious Makita bit holder. ...The clip on my holder securely attaches to the tool,...

Alphabetical/Drill Bit holder for holding an entire 26 bit set. I designed it with some extra tolerance in the holes to make removal easier. printed at 10% infill with PLA. ...I need to work on the lettering underneath to fix the islands left from...

This is a versatile holder for the Harbor Freight drill bit set with 1/4 inch hex drive capability. It accommodates any 1/4 inch drive bits or tools, up to thirteen in total count. ... I prefer using Slic3r as my go-to slicer software.

This is a 2x1 gridfinity parts bin for storing drill bits. I designed it for my small collection of masionary bits with a few spare places for expanding in the future. D.I.Y. TINKERER https://www.youtube.com/c/diytinkerer - please visit my...

http://www.thingiverse.com/apps/customizer/run?thing_id=91035 Instructions Using the following options: Handle_Length set to 65 units Handle_Diameter adjusted to 15 millimeters Resolution improved to high-quality settings at 40 steps per mm...

This drill bit holder turns the traditional clip-in bit mount found on most power drills into a 3 bit mount. I made this for my Craftsman 19.2V impact driver. The extra length on the clip attachment is designed specifically for the long slot on my...

A simple screwdriver bit holder for a Dewalt cordless drill. There is no ready attachment point on this particular drill model so the holder is affixed using double-sided tape. (I find 'Alien' tape works well for this type of application.) This...