drill harbor freight 3d models
62041 3d models found related to drill harbor freight.thingiverse
I remixed this Drill Index https://www.thingiverse.com/thing:1769954 to fit this Harbor Freight 7pc Brad Point Drill Bit set https://www.harborfreight.com/brad-point-wood-drill-bit-set-7-pc-61640.html
youmagine
The bubble-pack these bits came in isn't a great toolbox carrier for 'em, and they're so small, they get lost very easily. ... This small sliding drawer box has a friction-stop when closed. It fits the Harbor Freight 61526 drill bits pretty well.
cults3d
Quick holder designed for Harbor Freights Center Drills 60381, 42280 The two indentations in the rear are for gluing 18x5mm magnets. ...Clearances are 0.20 in the holes to compensate for prints.
thingiverse
Quick holder designed for Harbor Freights Center Drills 60381, 42280 The two indentations in the rear are for gluing 18x5mm magnets. ...Clearances are 0.20 in the holes to compensate for prints.
thingiverse
This is a basic holder for a Harbor Freight 20v drill. ...
prusaprinters
I was sick of the crappy, cracked case that came with my cheap Harbor Freight drill bits, so I decided to make a slightly less crappy holder for them. Remove the 3 orange pieces inside, cut off the excess on the sides, and shove them in here for...
thingiverse
This a fairly simple flange mount for a harvested motor from a discount drill from Harbor Freight. I made this mount, along with the rear strap, to mount 4 motors on a lightweight robot platform. ... ...
thingiverse
This is a drill bit holder for the harbor freight drill bit set with 1/4" hex drive. It can hold any 1/4" drive bits or tools, up to thirteen (13). I use slic3r for my slicer. ... Enjoy.
thingiverse
I broke my switch cover and needed a new one. ... I printed the source file and found it way too big. HF Item number 38144 13" Drill press
thingiverse
Flange mount for motor and gearbox 18v Lithium Warrior Harbor Freight drill to be mounted for a robot.
thingiverse
in the works......... ...This is a replacement for the factory depth stop for the bench-top harbor freight drill press.. ...also has additional hole for accessories..
cults3d
in the works......... ...This is a replacement for the factory depth stop for the bench-top harbor freight drill press.. ...also has additional hole for accessories..
cults3d
Chuck Key Holder for my Harbor Freight tiny Drill Press. Clamps around the main support column. Uses x2 4-40 pressed inserts and x2 4-40 screws. ... Printed with PETG filament.
thingiverse
Chuck Key Holder for my Harbor Freight tiny Drill Press. Clamps around the main support column. Uses x2 4-40 pressed inserts and x2 4-40 screws. ... Printed with PETG filament.
cults3d
Hardware: (Qty 1) M5 x 16mm Cap Screw (Button Head Cap / Phillips Head is preferred) (Qty 1) M5 nut Guide Buying Options: - Maker86 Industries Listing: https://maker86.com/shop/ols/products/rotary-tool-guide-compatible-w-harbor-freight-drill-master...
thingiverse
This is a simple Rotary Guide that fits the $10 Harbor Freight Drill Master (63235). It was designed for people doing extruded polystyrene carving... aka Tombstone carving. Hardware: (Qty 1) M5 x 16mm Cap Screw (Button Head Cap / Phillips Head...
thingiverse
While moving my older Harbor Freight floor drill press to my new workshop, I broke the front panel that holds the power switch and light switch. Several years in the Texas heat had made the plastic very brittle, and it broke at every attachment...
cults3d
While moving my older Harbor Freight floor drill press to my new workshop, I broke the front panel that holds the power switch and light switch. Several years in the Texas heat had made the plastic very brittle, and it broke at every attachment...
thingiverse
Total cost for the conversion not including shipping is; Fasteners $0.92 O-ring $0.65 Bearings $2.98 PLA Filament $1.16 Total of $5.71 O-ring spec https://www.grainger.com/product/GRAINGER-APPROVED-Round-222-Medium-Hard-Neoprene-1BUX9 Bearings...
thingiverse
I wanted a guide for my drill press in order to get my holes centered on a pipe. ... Nothing fancy but it seems to do the trick.
thingiverse
First day I had my hand-me-down bench-to Harbor Freight drill press I carelessly snapped the plastic depth stop collar. In a jiffy using FreeCAD, I was able to model a new one and have it printed out. ...Let me know if there is anything that needs...
cults3d
Includes 2x Drill Guides - 1 for Pigtails and 1 for Ethernet and Power Glands Holes sizes are for 1/8" Drill Bit, then use a step bit to the correct size of your glands
thingiverse
... in the best print orientation. The upper parts are provided inverted for the way that they will be used when mounting the rotary tool. [Harbor Freight Drill Master Rotary Tool](https://www.harborfreight.com/rotary-tool-kit-80-pc-63235.html)
thingiverse
The vise grip style drill press clamps available from Harbor Freight (and perhaps elsewhere) are really handy, but they will mar softer materials like aluminum. I didn't want the surface of the piece I was drilling to have marks left on it by the...
prusaprinters
I had a cheap (7.49) set of Harbor freight Titanium Hex Shank Drill Bit Set, 13 Pc. lying in the bottom of my tool box and decided the only way I was ever going to use them is if they where organized and in a case. ...So I got out the calibers and...
thingiverse
This was a replacement Drill Press Depth Stop for an 8 inch 5 speed no name drill press from harbor freight and other cheap hardware stores. ...Print Settings Printer Brand: Ultimaker ...
thingiverse
This is a magnetic bit holder for a Harbor Freight Bauer 20V drill or driver. It uses two 8x2mm round magnets that you must glue in. ...The holder has two 15mm deep hex slots for shorter bits and can hold a long bit or drill bit on the outside.
thingiverse
This rear mount is a complementary piece to the flange mount (http://www.thingiverse.com/thing:684314).
thingiverse
Customized version of https://www.thingiverse.com/thing:3240063 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=3240063
thingiverse
This is a replacement power switch cover for a Harbor Freight/Central Machinery 8" Drill Press. It was a very snug fit into the plastic enclosure. ... You might want to downsize to 99%.