drip line 3d models
154232 3d models found related to drip line.thingiverse
Irrigation drip line spike. Great for 1/4" or smaller line that waters a tomato plant for example. ...
thingiverse
A simple clip to hook a 6mm drip line to a FlorafFex FloraCap. It replaces a FloraClip. ...
thingiverse
This drip line clamp is designed to slip over the edge of a 1 inch board (I'm using Trex material) and hold a 1/2 inch (.7 in. O.D.) drip line. There is a hidden channel that will accept a small 6 inch zip tie to secure the line if necessary. ... There...
thingiverse
... Ender3, in PLA, which takes about 1.5 hours. They are 4 inches long, and print quickly. With soft garden soil, they easily press right in, and hold a 1/4" drip line or soaker line in position quite well. No supports needed. ... 100% infill
thingiverse
This clip will pressure fit onto a 5/8" board and allow you to run 1/4" garden drip line or up to 1/4" of wires behind the board. Currently using to run driplines along a planter box. Can be used under eves or along a wood fence. Can be scaled as...
thingiverse
This is a drip line stake inspired by Bocklar and tinkerur. Modeled in Autodesk 123d design software. ... Added vertical stake 5/14/19
thingiverse
I needed a way to get my hanging baskets disconnected from my drip lines when storms approached or to change them out without removing the lines and stakes and destroying the plants. These are simple twist on - twist off couplers that connect to drip...
thingiverse
I needed a way to get my hanging baskets disconnected from my drip lines when storms approached or to change them out without removing the lines and stakes and destroying the plants. These are simple twist on - twist off couplers that connect to drip...
prusaprinters
Easy-to-use irrigation clips for securing .700" (OD) and .250" (OD) drip irrigation lines. ...Simply attach the clip to the line and press into soil to secure.Note: clips are sized to nominal dimensions, you may need to scale up or down slightly to get...
thingiverse
Easy-to-use irrigation clips for securing .700" (OD) and .250" (OD) drip irrigation lines. Simply attach the clip to the line and press into soil to secure. ... Note: clips are sized to nominal dimensions, you may need to scale up or down slightly to...
prusaprinters
I needed a way to get my hanging baskets disconnected from my drip lines when storms approached or to change them out without removing the lines and stakes and destroying the plants. These are simple twist on - twist off couplers that connect to drip...
cults3d
Also take a look on: Seedling greenhouse from Ikea Trofast (https://www.thingiverse.com/thing:4848209) Micro drip line (4.6mm) holder on the wall (https://www.thingiverse.com/thing:4851701) Vertical holder for Gardena micro drip line, 4.6mm...
thingiverse
Also take a look on: [Seedling greenhouse from Ikea Trofast](https://www.thingiverse.com/thing:4848209) [Micro drip line (4.6mm) holder on the wall](https://www.thingiverse.com/thing:4851701) [Vertical holder for Gardena micro drip line,...
cults3d
Also take a look on: Ikea Trofast mount for 4.6mm micro drip line (https://www.thingiverse.com/thing:4851700) Seedling greenhouse from Ikea Trofast (https://www.thingiverse.com/thing:4848209) Vertical holder for Gardena micro drip line, 4.6mm...
thingiverse
Also take a look on: [Ikea Trofast mount for 4.6mm micro drip line](https://www.thingiverse.com/thing:4851700) [Seedling greenhouse from Ikea Trofast](https://www.thingiverse.com/thing:4848209) [Vertical holder for Gardena micro drip line,...
thingiverse
Customized version of https://www.thingiverse.com/thing:3641975 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=3641975
thingiverse
Customized version of https://www.thingiverse.com/thing:3764039 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=3764039
thingiverse
Customized version of https://www.thingiverse.com/thing:3764039 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=3764039
thingiverse
Customized version of https://www.thingiverse.com/thing:3764039 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=3764039
thingiverse
I needed a plant spike-type dripper that delivers the nutrient solution below the surface but near the top. This works with approx. 0.170 ID tubing. It is about 3 inches long and the hole goes through both sides. The internal cavities are diamond...
thingiverse
Customized version of https://www.thingiverse.com/thing:386904 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=386904
thingiverse
Stake to hold 1/4" dripline or 1/4" soaker hose in place. ... Stakes are 4" long and more sturdy (and cheaper) than the stakes you get from the home improvement stores.
thingiverse
Drip end can lock and unlock by tightening/loosening locknut to release the drip tubing for easier exchange than a traditional barbed fitting in the event of clogged/worn-out line. Requires ABS filament for strength. Recommend Max temp and higher...
thingiverse
So I created this cover/straightener, pretty much like a hexagonal drinking straw, that slides over the drip irrigation line to keep it straight (and also protected from damage such as solar UV and shovel nicks). I used a pentagonal design which...
thingiverse
This is a cover I designed for running two drip irrigation lines neatly in parallel. The bottom is open so the tubing can be pressed into the completed cover without disconnecting any irrigation lines. Default dimensions are for 0.245" OD tubing...
thingiverse
Clamp for 1/2 inch main line used for drip irrigation. Use a nail to affix to wood. I created and printed a bunch of these since I did not order enough of these. I used long nails I got from Harbor Freight. These have held up pretty well for...
thingiverse
This is a thinner version of my previous 1/2 inch poly main line holder. This is designed to work with #16 wire nails. I used #16 x 1 1/2 inch nails to attach the 1/2 poly mainline to the underside of our deck. I printed using PLA at 40% infill,...
grabcad
In-Line type drip emitter with 3 Configurations1- Original2- Chamfer 0.3mm3- Fillet 0.3mmthe CAD files are to support the member "abcd 720643" https://grabcad.com/groups/freelancers/discussions/sir-can-anybody-tell-how-to-make-this-design
thingiverse
An adaptor for connecting 4mm drip line to 13mm poly tube.