dropcam window mount 3d models
377468 3d models found related to dropcam window mount.thingiverse
http://www.thingiverse.com/apps/customizer/run?thing_id=189568 Instructions Using the following options: TAPE_LENGTH = 10 WINDOW_ANGLE = 0 DROPCAM_SHAFT_DEPTH = 25 AIRSPACE_WIDTH = 10 TAPE_WIDTH = 20 CORNER_PROTECTION_R = 5 CORNER_PROTECTION_H = 0.25...
thingiverse
This is a Dropcam Pro window mount based on the window mount by robcurtis, however, I remixed it to eliminate the blind-spots (in the corners of the video) caused by the original design's round aperture. I also added two additional holes, which I...
thingiverse
Fantastic design by buckyball, works like a charm... ... just added some vent holes (purely out of paranoia).
thingiverse
Window mount for dropcam with 20 degrees of tilt. ...VHB used to adhere to window.
thingiverse
A mount to hold a Dropcam Pro against a window at an angle. ... Instructions After printing, the side without the smaller ring should be sanded smooth and cleaned so the mounting tape will grip the mount.
thingiverse
http://www.thingiverse.com/apps/customizer/run?thing_id=189568 Instructions Using the following options: WINDOW_ANGLE = 15 TAPE_LENGTH = 10 DROPCAM_SHAFT_DEPTH = 25 CORNER_PROTECTION_R = 5 CORNER_PROTECTION_H = 0.25 WALL_THICKNESS = 2 $fn = 128...
thingiverse
http://www.thingiverse.com/apps/customizer/run?thing_id=189568 Instructions Using the following options: AIRSPACE_WIDTH = 5 DROPCAM_SHAFT_DIAMETER = 48 WINDOW_ANGLE = 15 $fn = 128 DROPCAM_CONNECTOR_DEPTH = 2.5 CORNER_PROTECTION_R = 5...
thingiverse
http://www.thingiverse.com/apps/customizer/run?thing_id=189568 Instructions Using the following options: DROPCAM_SHAFT_DEPTH = 25 WINDOW_ANGLE = 10 $fn = 128 DROPCAM_SHAFT_DIAMETER = 48 AIRSPACE_WIDTH = 5 TAPE_LENGTH = 10 WALL_THICKNESS = 2...
thingiverse
http://www.thingiverse.com/apps/customizer/run?thing_id=189568 Instructions Using the following options: WALL_THICKNESS = 2 WINDOW_ANGLE = 15 CORNER_PROTECTION_R = 5 CORNER_PROTECTION_H = 0.25 AIRSPACE_WIDTH = 5 $fn = 128 DROPCAM_CONNECTOR_DEPTH =...
thingiverse
http://www.thingiverse.com/apps/customizer/run?thing_id=189568 Instructions Using the following options: CORNER_PROTECTION_R = 5 CORNER_PROTECTION_H = 0.25 TAPE_LENGTH = 10 AIRSPACE_WIDTH = 5 DROPCAM_SHAFT_DEPTH = 25 DROPCAM_SHAFT_DIAMETER = 48...
youmagine
Ultimaker 2 mount for Dropcam. ... This was designed to be used with the provided dropcam mount. My Dropcam public live feed. ... http://dropc.am/p/Xi8IRr
thingiverse
I needed to ceiling mount my dropcam pro's, but didn't have the original base adapter. Most of the existing mounts online are circular, but I wanted to keep using the original metal frame. I just needed a cradle mount. I found a really good one for...
thingiverse
This is a mount for a Dropcam for the TAZ 5. It clips onto the front bracket of the Y Axis and has adjustable camera angle. This gives me a better view of the print then the typical top down view. STLs are attached and the parametric model is...
thingiverse
... Print this thing however you want, put your Dropcam camera on it and fasten to your tripod shoe. Update 12/25/2012 - I printed these in two parts. Assembly is: insert tab-A into slot-B and align with a gentle tap of a hammer or putty knife handle.
thingiverse
... or on the corner mount then insert the support arms and then place the camera in the ring and on the arms. Permits same range of flexibility as original dropcam mount. ... Primarily, I wanted something lower profile at oblique angles and in white.
thingiverse
I took apart the Dropcam's original mounting bracket by popping off the end caps on the hinge and unscrewing it. I used the top half to hold the camera and with a bolt and lock nut fit it to this webcam mount for use on the Creality CR-10. It's a...
thingiverse
Then designed this mount for clipping it to the front of the Makerbot Replicator 2X. Work should always be this fun. ... Instructions I printed this at the standard resolution with a 10% infill on a...
thingiverse
My camera feed: http://printrbot.rocks/ Here is a link to the Dropcam used:http://amzn.to/1TL1OI6 Instructions I printed mine using supports. Also I use M3 VHB double sided tape to adhere the mount to the bed. I used a micrometer set to 87mm to...
cults3d
A mounting bracket for the Dropcam & Dropcam Pro webcams. Designed to allow you to attach the Dropcam to your Replicator 2/2X. Two lengths of camera mount are included; one for shorter builds and another for lots of Z-axis depth. ... The camera mount...
thingiverse
This is my heavy duty Dropcam mount. I liked the first one I made (http://www.thingiverse.com/thing:881044) and I wanted a little more flexibility in view angles, so I made this one. Link to Dropcam: http://goo.gl/wkz429 Warning this will not fit...
thingiverse
Mount for dropcam ( nest cam ). Used with existing metal holder/screws. ...Print Settings Printer Brand: Ultimaker Printer: ...
thingiverse
needed a solution to mount dropcam in 90 degree corner of room, enjoy the progression, maybe some parts are of help to you, sized for dropcam3-hd/8 with micro usb port
thingiverse
This is a derivative of the Dropcam Replicator 2 Corner Mount, I just made it fit to the PowerSpec 3D Pro enclosure. The credit remains with the original author. You can use it on any corner. Instructions As the mount is kept outside of the printer...
thingiverse
This serves as a Dropcam mounting kit for the Replicator 2. The kit will allow the Dropcam to view the printing platform from above. Instructions Thank you to dmpmassive and Waltermixxx for their...
thingiverse
A mounting bracket for the Dropcam & Dropcam Pro webcams. Designed to allow you to attach the Dropcam to your Replicator 2/2X. Two lengths of camera mount are included; one for shorter builds and another for lots of Z-axis depth. The camera mount...
thingiverse
For using a Dropcam Pro to monitor and record prints with a Zortrax M200. ...Let the sweet timelapse videos flow!
thingiverse
The case comes in 2 parts: the main case that holds the Dropcam main body and has room for a USB cable, and an insert to keep the camera in place when mounted. The cable is routed to the side to accommodate the wire running down the door frame and...