drum clamp 3d models
51680 3d models found related to drum clamp.thingiverse
I designed this to clamp a 15 mm "support rod" to the 35 mm leg of an Alexis Nitro Mesh kit. The centre bolt can be loosened with a hex wrench to allow you to change the angle (can't be adjusted while attached to the 35 mm leg). The swivel has 15°...
sketchfab
Fork-mounted drum clamp. Захват бочок на вилочний навантажувач. Захват бочок з монтажом на вилах. ...Захват на две бочки Навісне обладнання від ТМ Agri Advantage
prusaprinters
Mix some epoxy and spread it onto the flat surface of that clamp where the dowels were placed, then push the other clamp onto it so that the dowels fit into its holes as well. After the epoxy is cured, it is ready to use. ...Optional: put a very small...
thingiverse
This is a modification to fit the drum clamp to any microphone. There are files missing regarding the varying head sizes but the main microphone holder is there. Aside from the main design, I wanted more versatility with my microphone options since I...
thingiverse
I modeled this after the rack clamps that come with a Roland V-Drum electronic drumset. I would imagine that this would also work with an acoustic drum rack that uses standard 1.5" round tubes. ...The holes for the bolts and nut traps are sized for 1/4"...
thingiverse
This is a clamp designed to attach to a vertical drum stand (cymbal stand). In one of the photos, I show a triangle and hand chimes that are hung precariously from a knob. This project was a fix for that mess. I ended up making a version 2...
thingiverse
My wife lost the plastic collar/sleeve for her drum kit clamp that holds the Tom/Cymbal to her drum kit. Yamaha doesn't sell just the collar/sleeve - you have to buy the entire clamp assembly - so I printed her a new one. Her kit is a DTX502 series...
thingiverse
One of my original clamps for my floor tom snapped in half (think i did it up to tight) so i tinkered this in about 15mins my first every thing! printed on my ultimaker in PLA with 0.8mm wall thickness and 33% infill it took a little over 2 hours at...
thingiverse
See on one of the pictures the little white layer between the clamp and the rack. It is there for giving a good Grip on the DrumRack. Since without it, I had some issues with not being properly fixed on the Drumrack. <br></br> There is also a...
thingiverse
Customized version of http://www.thingiverse.com/thing:747679 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=747679 Instructions Using the following options: DecoSu...
thingiverse
Replacement cymbal clamp for the Legacy DD502 electric drum kit. Might be compatible with similar kits that use a ~1.5" (37mm) frame and 19mm poles to mount cymbals. Reuses the metal parts from the clamp that probably just failed on you. ... Open SCAD...
thingiverse
This part is to replace the clamps used on Harmonix Rock Band 3 Drum Kit (mine is for PlayStation 3 but I suspect they're all the same). The print is designed to hold a #8 nut with use a #8 x 3/4" bolt. Be sure to use support (with low % fill) to...
thingiverse
It is a rack clapm for the vertical side tubes on the Alesis nitro kit drumrack. ...Can be rotated.
thingiverse
This is based on a drum rack clamp from a Roland electronic drum set. The clamp is used to join 2 pieces of 1.5" tubing - should work with any brand of drum rack that uses standard round tubing. The hardware required are 2 drum lug screws 1.5" long...
pinshape
clamps rackear for electronic drums racks
thingiverse
The bolts and wing nuts are M6 Possibly the material you print the clamp with will require a bit of extra filing or sandpapering. Please note that the inconsistencies you see in the picture will NOT be visible in the actual print, fortunately,...
thingiverse
These clamps are for securely mounting a Drum Fan to a surface. 4 clamps recommended. Mounts with standard 1" or 1.25" deck screws. ... Works with the rolled steel rear edge on these 2 fans (17.375" diameter) Caterpillar FAN:...
thingiverse
This is a drum stool threaded clamp that I fixed for a friend. The threads had gone completely so the stool wouldn't hold any person. I recreated a replacement part and printed out of Nylon. Works and fits perfectly. ...The stool may actually be better...
thingiverse
... rod. You need a 12mm threaded rod to screw directly into the plastic of the adapter to support a tom. Without the adapter the clamp can serve as direct support for the TD9kx module for example. ... you can use M6 screws to tighten the clamps
cults3d
... threaded rod. You need a 12mm threaded rod to screw directly into the plastic of the adapter to support a tom. Without the adapter the clamp can serve as direct support for the TD9kx module for example. ...you can use M6 screws to tighten the clamps
cults3d
... I connected this pad as a quad trigger to a Roland TM-2 trigger module and connected it with the self-made rack clamp to my e-drum rack. Principle: The necessary sensors are easy and inexpensive to buy in online stores and the wiring is a breeze.
thingiverse
These clamps are for securely mounting a Drum Fan to a surface. 4 clamps recommended. Mounts with standard 2" or 1.625" deck screws. I do not recommend using these clips to attach the fan to a filter box which is mounted on a wall or the ceiling.
thingiverse
Made some change to the model to use Drum Tuning screws and 7/32 nuts The joint is made with an M5 screw and auto lock nut Can be used with the same connection of the original model
thingiverse
I wanted to be consistent with the larger kit my drum teacher uses, so this clamp lets me re-position the ride cymbal. Printed in PLA plus. Use M6 nut in the slider, and a M6*30 bolt in the wing nut. ... 5% infill on clamp, 20% on wing nut and...
cults3d
This is a T for roland drum rack (hardware), for 38mm tube Print this model stand up with automatic supports enabled everywhere (not just on plate) Use 30% infill min, and résolution of 0.2mm Happy printing drummer's ! ... David.
thingiverse
This is a T for roland drum rack (hardware), for 38mm tube Print this model stand up with automatic supports enabled everywhere (not just on plate) Use 30% infill min, and résolution of 0.2mm Happy printing drummer's ! David. ...