dry box container 3d models
371994 3d models found related to dry box container.thingiverse
Dessicant box which fits into this sterilite drybox design: https://www.thingiverse.com/thing:2929701 Fill with silica gel, damp-rid, sieve, etc. Air gaps aren't quite small enough to keep all of the damp rid inside, but it will keep it under...
prusaprinters
Allows a bowden tube to be connected for easy filament routing and reduced moisture ingress.Can be stacked with additional containers.Room for plenty of dessicant (loose beads or packages) below the filament spools!Full project description, original...
thingiverse
This is a Shelf (Container Holder) for Home made Rubbermaid 21cups Dry Box Container. Can be used with "https://www.thingiverse.com/thing:5371563" or any other one. This can be mounted on the side of the printer or cabinet like in my solution. ...
thingiverse
Filament Dry Box Using Daiso Container 5.5L Clear Universal Spool Holder Hole Size 68mm - 36mm 608ZZ bearing * 2 Rod Holder Bottom M8 Long bolt 110mm * 1 M8 nut * 1 M3 * 8mm bolt and nut * 4 Infill:90% Rod Holder Top M3 * 8mm bolt and nut * 2 ...
thingiverse
Container Holder For Box Original holder: https://www.thingiverse.com/thing:4164009, **thank you joreal!** Print holder at 0.5 line width. Place heat-set inserts in the holder. I printed veritcally, but flat on back should work too? I used...
prusaprinters
Loved the idea for a cover for the slica in the dry box container. I had a challenging time with the silica moving underneath the ring, so I merged the ring to the tray. ... Please enjoy</p>
thingiverse
Circular container for silica gel. ...Capacity for 100g in a thin layer
prusaprinters
The cover don’t interact with any filament spool, since the cover is around 7 mm lower then the top of the container.Building instructionParts:If not already available silica gel (I used this: ST-Trockenperlen)3D printed parts for one set:1 x...
thingiverse
A silica gel container for use in a filament dry box. The lid is fixed with rubber bands or TPU bands. Attach it to the corner of the box with double-sided tape, but fix it lightly enough that you can remove it. ( only prevent sliding sideways ) It...
thingiverse
A small container to hold silica desiccant beads inside a dry box. ... I sized it specifically to fit into the tube of a horizontally-mounted Hatchbox spool, but it should work for spools up to 60mm internal diameter (or just don't stick it in a spool...
prusaprinters
A small container to hold silica desiccant beads inside a dry box. ...I sized it specifically to fit into the tube of a horizontally-mounted Hatchbox spool, but it should work for spools up to 60mm internal diameter (or just don't stick it in a spool --...
thingiverse
For each dry box you will need, - 1 IKEA 365+ 10.6l food container with lid (I won't quote part numbers as they vary by region but the container is 32cmx21cmx23cm) - 8 608ZZ Bearings - 4 M3 x 8MM Hex Socket Head Cap Screws - 2 straight through PTFE...
thingiverse
Dry Box for 3D Printer filament using DAISO 5.5L container. (DAISO 5.5L container: size 29cm(11.4 in) x 22.2cm(8.74 in) x 11.9cm(4.68 in) ) Original Drybox (hitoriblog's Drybox): https://www.thingiverse.com/thing:4563022 From that model, I modified...
thingiverse
This allows mounting a cheap hygrometer (https://www.amazon.com/gp/product/B08ML6PJVF or https://www.amazon.com/gp/product/B08DJ24YMW) into a 135.2oz Cereal Container (https://www.amazon.com/gp/product/B081F6X2W2) directly into the existing hole in...
thingiverse
I needed a dry-box for my filament and wanted something that I could print from, as well as being relatively small because I don't have much space. I was looking for something that was big enough for a single spool. I found Cereal Tupperware and...
thingiverse
These were designed to be applied to the top lid mounts on this filament dry box (http://www.thingiverse.com/thing:961881). A 1.75mm and 3mm version has been provided. In my box I had to dremel the plastic inner rim to fit the curve of the...
thingiverse
Silica gel holder for Rubbermaid 21cup. ... Download the no hygrometer version from https://www.thingiverse.com/thing:3222374 and scale down to X and Y to 80%.
thingiverse
Organize your filament spools in your dry box (specifically for Sterilite 32 Quart Clear Plastic Stacking Storage Container with Gasket Lid) using this dual-rod storage solution! You'll need 6 nuts, 4 rods, 1 joint, 1 coupler, and 2 (optional) rod...
thingiverse
The filament container or **_Dry Box_** contains packets of desiccant that absorb any humidity that does infiltrate the container. Except for a very short piece of filament that is within the *MMU2* feeder, no part of the filament is exposed to the...
thingiverse
The dry box contains a heater to keep the filament warm along with desiccant and a PID controller for the heater. Store 30 rolls or more of filament in just one box! You can watch the video on how this box was made here...
thingiverse
... The filament comes out of a hole that's the right size for a Bowden tube, so that the filament makes it to the 3d printer as dry as it was inside the box. There is a holder that you screw on the spinner, and you can put silica sachets inside.
thingiverse
Plastic Container Dry Duct is a tool used to dry plastic containers quickly. Set the dry duct in the spout of the plastic container and blow it with a fan. Dry air flows into the plastic container. Moist air comes out of the plastic container. *...
thingiverse
This is a dry box for filaments put on my printer enclosure with temperature/humidity sensor. I tried to install a heater, but it did not improve the humidity. The humidity is from 18% to 20% with only the silica gel beads. I originally bought a...
prusaprinters
print each partenfill the box with silica gel packets ⚠ you may have to enlarge the holes with a drill
prusaprinters
print each part enfill the box with silica gel packets ⚠ you may have to enlarge the holes with a drill
cults3d
Sealed container for dry fuel, capacity 5 pellets with a diameter of 30 mm, height 10-11 mm. ...Container dimensions 80 mm, diameter 43 mm Link CONTAINER FOR SPICES https://cults3d.com/en/3d-model/various/konteyner-dlya-spichek