dryer knob replacement 3d models
173172 3d models found related to dryer knob replacement.
thingiverse
This is a replacement start knob for dual washer/dryer that we recently picked up used. It was missing said knob, so made a new one. The knob's original dimensions put it around 37.5mmx~37.5mm Shaft should fit a post that is 6.3mmx5mm quite snuggly,...
thingiverse
The knob broke on my washer/dryer and I saw replacements were like $15. I thought to hell with that and made my own. I designed it to fit the metal sleeve that fit inside the broken knob but found its not needed at all. I wasn't going for an exact...
thingiverse
Angry after having to use a pair of vice grips to start my dryer for a few years, it dawned on me one drunken evening that I could easily model and print one. I whipped this out in about 5 minutes, printed it, and it slid snugly on, the first try....
thingiverse
This is a replacement knob for washers and dryers that utilizes an M4 nut and set screw to grasp the remaining D-Shaft of the washer or dryer. There are 50mm and 70mm (diameter) variants available, and I would be willing to procure larger sized per...
thingiverse
Customized version of http://www.thingiverse.com/thing:54024 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=54024 Instructions Using the following options:...
thingiverse
Modified to a 70mm overall width to match old broken one, removed shaft extension and modified hole to 6.5mm (1/4 in). You will need to take old metal D adapter and place it in the hole to hold the shaft securely. Tamp it down into the hole...
thingiverse
Customized version of http://www.thingiverse.com/thing:54024 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=54024 Instructions Using the following options: HoleDepth...
thingiverse
Customized version of http://www.thingiverse.com/thing:54024 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=54024 Instructions Using the following options: TimerKnob...
thingiverse
Customized version of http://www.thingiverse.com/thing:54024 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=54024 Instructions Using the following options: Pointer2...
thingiverse
Customized version of http://www.thingiverse.com/thing:54024 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=54024 Instructions Using the following options:...
thingiverse
Customized version of http://www.thingiverse.com/thing:54024 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=54024 Instructions Using the following options:...
thingiverse
Customized version of http://www.thingiverse.com/thing:54024 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=54024 Instructions Using the following options:...
myminifactory
Replacement Admiral Company Clothes Dryer Knob for model AYE1000AYW. ...This is a fun replacement knob for the original.
thingiverse
I just need a quick replacement knob. Printed on a MB Gen 5. ...100% infill.
thingiverse
GE Dryer knob replacement. ...Reverse Engineered to be the exact size of most GE dryer knobs.
pinshape
Dryer Knob replacement for GE laundry dryers. Some support to remove on the back side of knob if printed handle side up. ...Best to print this way as the rough surface from the support is hidden.
thingiverse
My dryer knob broke.......... here is the replacement. ...Check you old knob to make sure it fits your post.
thingiverse
Replacement dryer knob. I got tired of paying 16+ dollars for replacement knobs that broke within a week. ...So I printed one for less than a dollar and its been working for months.
thingiverse
Replacement 1/4" d-shaft dryer knobs. I needed the shaft to extend down lower than the knob body. In order to keep this design printable without supports, the knob has a rounded handle and is printed "upside down". ... The original openscad file is...
thingiverse
Replacement knob for clothes dryer after the original developed a crack. This is the first thing I've designed and printed from scratch (designed in tinkercad in around 30min), and the most practically useful! ...Saved me from potentially buying a...
thingiverse
Knob for Frigidaire Dryer. ... Commonly the post on the inside cracks on the original at the flat side corners.
thingiverse
Dryer know I modeled for a friend. ...Hopefully it helps some one else. I designed this in Fusion 360 from measurements taken from the original knob.
prusaprinters
Replacement 1/4" d-shaft dryer knobs. I needed the shaft to extend down lower than the knob body. In order to keep this design printable without supports, the knob has a rounded handle and is printed "upside down". The original openscad file is...
thingiverse
This is my first 3d printed home repair, which is a replacement knob for my dryer, which was missing when we moved in. (Forgive the poor print quality of the photo. I'm still getting used to my first printer, having had it less than a week, and I...
prusaprinters
This is for a whirlpool dryer. I did a color change at .6 when printed at .02 layer. ...Added gcode with that included. </p>