dual 18650 box mod 3d models

Im new to this but here it is, a dual 18650 box mod

Simple elegant dual 18650 box mod. Model for 24mm atomizer. ...You can use 12mm ( http://ali.pub/1ld7c3 ), 16mm ( http://ali.pub/1ld7fz ) or tact button ( http://ali.pub/1ld7gy bracket included) only with the last enough space for a voltmeter (...

dual 18650 box mod with voltage meter parts needed : 22 2mm dia x1mm n52 neodymium disk magnets 2 Keystone 209 battery connectors 2 Keystone 228 battery connectors 1 lcd voltage meter 1 short 16mm push button 1 22mm 510 connector 1 N-Channel Mosfet...

A dual 18650 unregulated box mod. the fire button hole is for a 16mm push button and the top is for a standard 510 connector. ...the battery sled can hold standard clip-on battery contacts.  if you have simplify 3D or a slicer that allows you to set it...

dual 18650 box mod with voltage meter parts needed : 22 2mm dia x1mm n52 neodymium disk magnets 2 Keystone 209 battery connectors 2 Keystone 228 battery connectors 1 lcd voltage meter 1 short 16mm push button 1 22mm 510 connector 1 N-Channel Mosfet...

Dual 18650 box mod prototype

Unregulated Dual 18650 Box Mod Fire Button 16 mm Drip Cup 11 mm (510 Connector - Fat Daddy) 18650 Battery More on: https://www.shapeways.com/shops/vasodipandora

2- batteries 18650 10 mm metal buttom  510 conector  it have enough free space for a mosfet and a resistence.

There are many different designs out there, but I want a box that was as small as possible. After a lot of modification and prints this is what I decided on. It has about the same dimensions as a Hammond 1590g box. The box is designed for use with a...

This is a remix of Element18592's upload of "Unregulated Dual 18650 Box Mod (Vape)" at http://www.thingiverse.com/thing:1310499 . ...For best quality I recommend printing it with 100% infill and maximum layer resolution (I used 0.06 mm) List of changes:...

This is a dual 18650 unregulated box mod. ...Printed with Robo3D on low quality Parts: 1x 15k Ohm resistor 1x IRLB3034PBF mosfet 1x 12mm short thread/shallow depth momentary push button 1x 22mm 510 connector 2x Negative battery contacts 2x Positive...

This is a dual 18650 unregulated box mod.Printed with Robo3D on low qualityParts:1x 15k Ohm resistor1x IRLB3034PBF mosfet1x 12mm short thread/shallow depth momentary push button1x 22mm 510 connector2x Negative battery contacts2x Positive battery...

This is my revision of another box mod. Added a bit more space to also allow a 20amp raptor chip. A few other changes as well. Uses: 1/8 X 1/8 magnets Keystone tabs (209, 228) 1s-6s volt meter 16mm button Lid can be found here: ...

This remix offers a bit smaller size in the box, a few cleanup areas, re-aligned the magnet holes for a better fit. The button hole is also removed so you can use any button you choose by edit or drill. I have also added a cover over part of the...

This is my revision of another box mod. Added a bit more space to also allow a 20amp raptor chip. A few other changes as well. Uses: 1/8 X 1/8 magnets Keystone tabs (209, 228) 1s-6s volt meter 16mm button 1/2" (.495 actually) pot Lid can be found...

First working version of my box mod. I used around the house parts to test fit and get working. Don't mind the burnt wire or the wonderful soldering, this is a low quality print so I did low quality work. If you build this and assemble it make sure...

Remix for personal changes. ...Magnet holes re-aligned with box changes.

... opening it with Slic3r or similar programs. Scale of the perimeter is true to a Hammond 1590g box, make sure your 3d printer is calibrated. Use Keystone 238 contacts. ...Originally made by http://www.thingiverse.com/ariuskooo/about Enjoy!

Design #5 of the dual 18650 Box Mods, designed with portability in mind! Supports dual 18650’s in either parallel or series configurations. Magnetic Lid comes with shell. Vanity Plate covers all electronic components inside the box. ...*Does not...

This is just a simple dual 18650 mechanical box mod. Instructions are below on how to get it operational. WARNING DO NOT USE IF YOU ARE A BEGGINER KNOW YOUR BATTERY SAFETY!!! Updates: I added the SolidWorks files if you want to edit and change it...

Best print in ABS or PETG with supports. ...Designed for Fat Daddy´s v4 low profile 510 and keystone battery connectors P/N: 228 and 209 Print Settings Printer: MakerFarm i3V ...

Component list: Component list: 1x NE555 pulse wave modulator: http://adf.ly/1Z4ljV 4x Keystone battery contact 5209: http://adf.ly/1Z4fzL 1x LCD Voltmeter: http://adf.ly/1Z4ln4 1x bottom feeder connector (10 or 12 mm, i attached two body version) 1x...

Fits like a glove! ... This is the lid for: http://www.thingiverse.com/thing:630413 orhttp://www.thingiverse.com/thing:630418 Uses 1/8 x 1/8 magnets Instructions Printed on my Flashforge Pro .1mm...

This is my revision of another box mod. Added a bit more space to also allow a 20amp raptor chip. A few other changes as well. Uses: 1/8 X 1/8 magnets Keystone tabs (209, 228) 1s-6s volt meter Otto P9 Button (.45 DIA) 1/2" (.495 actually) pot ...

Well I am taking my beginner CAD skills and working on them every day. I am very proud and excited with how this turned out after much fine tuning and revising. Works extremely well and I think it turned out awesome. Link to parts used Keystone...

Dual Box 18650 Projetei este modelo por que tenho vários suporte de baterias 18650 com proteção, que usarei para colocar as baterias.

Dual 18650 sled for the hammond 1590g box. The contact wells are very tight but the contacts WILL fit on. ...Everything is pushed as far to the right as possible to maximize working space on the left.

Dual 18650 sled for the hammond 1590g box. The contact wells are very tight but the contacts WILL fit on. ...Everything is pushed as far to the right as possible to maximize working space on the left.

this is a dual 18650 box with curved lid takes 16mm switch. mitec from varitube works best because it's a shorter 16mm switch... ...enjoy

this is a Dual 18650 series mod remixed from the Celtic skull floating around thingiverse. ...10mm 510 hole 12mm button hole keystone 209 & 228 battery sleds are offset on very bottom the right eye cold use more support added under the socket inside but...