dual fans 3d models

Tevo or MKS board cover with dual fans. Topped with dual 40 mm Noctua fans. If you don't have or have not tried Noctua fans, this should be your first upgrade. Keeps stepper motor drivers much cooler allowing for much better prints. Using a...

This is a remix for dual fans as the single fan on the side may not get to all the heat sinks for the drivers.

I removed the no longer needed stock display and added this block and two Nocturna Ultra quiet fans. ...Size 60mm by 25mm. used the 12 vdc version and added the buck converter. These are real quiet, only fan I can hear now are the hot end fans.

Dual fan laser air assist

https://www.etsy.com/uk/listing/1065848597/valve-index-minifan-dual-fans-frunk-mod?ref=shop_home_active_1&frs=1** Before you continue please read: I am not responsible for any damages that could occur from bad wiring/soldering, I use my fan mod daily...

I created this duct/bezel to bridge the gap between the fans and drywall on the other side. These are AC Infinity fans that you can get from Amazon. They are made for a stereo cabinet but I wanted them to vent a media closet. ...Print Settings Printer...

This mount is for the SKR1.3 board and holds two 40mm fans over the drivers. You will need 4 M3X30mm standoffs to mount the fan to the base. ...I used the ones with the male threads on one end and the femail threds on the other.

This one uses 2 30mm fans on each side to blow on the freshly extruded filament. I have it mounted on my printer and it works fantastic. I highly recommend PETG or ABS for the job. Happy printing!(Just a quick note. Ik this fanduct is wide, that is...

Dual Fan Remix

Front block with dual fans and Prox. ...sensor to be used with the back part of this thing: http://www.thingiverse.com/thing:1091103 you will need to place a washer behind the extruder to line up the extruder and hot end.

This is a re-mix of NeoTko's Symmetric Dual Fans (1) to fit my E3D-v6 hot end mount (2). The plate needs to be rigid, you should cut it in fiber based material (carbon, G10, ...). The fan shroud is the "For Amedee Mod Umofancap40x40v3" from NeoTko...

Renkforce RF2000 40mmx40mm Dual Fan

... mounted 7mm below the hot-end holder - G10 plate of 2.5mm - Scalable tops (spacers) of 1.4mm This is for an Olsson/E3D nozzle, the stock Ultimaker one is longer... (1): https://www.youmagine.com/designs/symmetric-dual-fans-umo-umo-30mm-40mm-50mm

Like to have easy and quick access to the sensor so I decide to make a mix from from original fan duct from @davidwyl that actually i already had in use and i like it Need to download the sensor mount ( SensorBlockUniversal.stl) from @MaddeMichael...

Read the instructions and post at Ultimaker at:https://ultimaker.com/en/resources/20503-ultimaker-original-dual-fans-upgrade Updated with step/rhino/3ds files of the 30x30 version so anyone can change it and make their own version. Updated with...

This is a Dual Fan setup for a Robo 3D with the Hexagon Hot End. There are 4 fan enclosures included, the front, rear and a rear with 2 mini IR sensor mount, one adjustable mount and one fixed. All 4 have a slider option to modify air flow. I...

This is a Dual Fan setup for a Robo 3D with the Hexagon Hot End. There are 4 fan enclosures included, the front, rear and a rear with 2 mini IR sensor mount, one adjustable mount and one fixed. All 4 have a slider option to modify air flow. I...

dual fan holder with a zip tie space for holding two fans onto a brushless motor.

Simply dual fan for Adventurer 3, fast and easy to print. ... No problem to change noozle.

40x40 dual fan mount used to cool down nozzles and extruder motor temporaily attachable to plates within thickness of 1.5cm

Dual Fan in Vulcanus V1 I Just Glow Them, You Can do the Same or You Can edit the X Model. Just Print. ...

This dual fan duct mounts two 40mm fans held in place by the hot end itself. Thus it will fit to most direct extruders as well as to Hexagons mounted to bowden extruders. Prints without support if your printer is well aligned. ... Use a M3 screw,...

Just a garden decoration -- a decorative dual-fan wind spinner I designed for the yard. Rotates to face the wind, and spins at even 2-3mph wind speeds with the right bearings. The two fans rotate in opposite direction. ... Needs 3 standard 608...

Dual Fan Enclosure. I have included the step files for any body wanting to change the mounting holes. Motors are connected in series so as to run slower and quiet. The motors are blowing over the controller boards to get max cooling. My aim is to...

Originally found this dual fan mount on Thingiverse: https://www.thingiverse.com/thing:2978427 Worked just fine, but I wanted to make it a bit sturdier and update the aesthetics plus it gave me a chance to practice with Fusion. You'll need 4 m3x20...

Labern's Dual Fan Shroud For Original and Olsson Heaters Block SetupsNEW, Have an I2k Shroud, It will set the shroud at the correct height when using the PTFE I2K insulator and the spring replacement found here:...

dual fan duct for the Prusa Mk3s with led mounts. It accepts 2 x 5mm leds and the power to my leds are ran independently via wall plug. (The only other real option is running a buck down converter to the power supply. Which I have not tested and...

This is a mod for the MK3 which allows dual blower fans on the hot-end for improved cooling. Electrically, you can split the power and ground wires from the existing fan and wire it into the new fan. This works well, actually requires minimal...

I designed this dual fan duct to make use of the two fan ports in the head, one is an always on 5v port, and another is PWM controlled port (via `M42 P15` gcode in case of Cetus CPU or M106 using TInyFab CPU). I designed this to use a 5015 blower...

-Setup- I used two 12V fans is series instead of 24V fans with this design mainly because I already had a few 25MM 12V fans already so that is what I started with and than I decided to go to 30MM so I kept it the same also it seems way easier to get...