duct tape gun 3d models
103999 3d models found related to duct tape gun.sketchfab
Black and silver duct-tape Camera model: Zivid One+ Small Working distance: 500mm
3docean
Duct Tape Very Detailed Duct Tape. The Model is Low Poly, and perfect for any game environments, such as fps horror, MMO, Survival, etc. It also fit perfect as an Item pickup in many game genres Model is unwrapped, and UV Mapped using...
3docean
Duct tape Sketchfab 3d preview: https://skfb.ly/G7ET Made with Cinema 4D r16. 163 polys. Includes: Cinema 4D project. Model in 3 formats (obj, fbx, 3ds). 6 .tga texture maps (Albedo, Ambient occlusion, Diffuse, Metallic, Normal map, Specular). ... ...
thingiverse
this is a tape holdet to put near your 3d printer so you can replace the painters tape easely
cults3d
You will need: 1 screw M 6x70 2 screws M 6x65 2 screws M 6x55 7 nuts M 6 2 washers M 6 1 spring 3 wooden screws 3,5x15 If you don't have a spring to brake the tape reel, I think you can easily replace it with cardboard washers. I lightly sanded and...
thingiverse
This is a 3d printable version of a mini tape gun I had laying around. It holds the standard tape dispenser rolls. You know, the little 3/4" rolls that you use to wrap presents with at Christmas time. It prints in 4 parts with support and the little...
thingiverse
Super-sized version of the mini tape gun. This version fits a regular 3 inch roll of packing tape. Post-Printing Hot glue the parts together. Sharpen the cutter teeth using a metal file and a lighter. Hammer the end caps into the spool. Put some...
prusaprinters
Super-sized version of the mini tape gun. This version fits a regular 3 inch roll of packing tape. Post-Printing Hot glue the parts together. Sharpen the cutter teeth using a metal file and a lighter. Hammer the end caps into the spool. Put some...
thingiverse
My wall mounting duct tape organizer. ...Tape width 50mm, inner diameter 75mm
thingiverse
... other items. Print two identical parts and snap them together through the duct tape roll. Fits a duct tape roll from Clas Ohlson with an internal diameter of 26.5 mm. ... Repository with FreeCAD design file: https://github.com/hsolg/duct-tape-spool
prusaprinters
... marker to make the banana look more real. Magnets of 8mm by 2mm if required (2 slots given). Might have to heat the duct tape part using the heat gun and bend it inwards to make it sort of a perfect fit for the banana! Category: Sculptures
thingiverse
Simply another Duct Tape Holder. Made for 50mm wide and 70mm round Tape. ... Screwed to my cabinet with two 12mm screws.
thingiverse
Tiny duct tape spool for bringing a small amount of duct tape on the go. Print two identical parts and hold them together. The first round of tape will attach the parts to each other. ... This spool is designed for a tape width of 36 mm.
thingiverse
A guide that goes onto your duct tape roll so you can rip it without splitting it down the middle while also knowing where you left off on the roll. ... Instructions Just print and fit snuggly to your roll of duct tape.
thingiverse
A jig to mark the middle of a strip of duct tape. 1. Print and attach a top and bottom part. Make sure the arrows point in the same direction. 1. Pull out a strip of duct tape. 1. Thread the tape through the jig, with the glue side facing...
thingiverse
This is my 2nd (improved) version of a duct tape dispenser for big rolls. ... The teeth are not sharp enough so I recommend you use knife to make it sharp.
thingiverse
... box. Dimensions of the project: Width:60mm Length:110mm Dimensions of Duct Tape: Width:45mm Length:47,50mm I hope it works for you too. ... ///Social Media/// Youtube: idilbaz (https://www.youtube.com/channel/UCyZtXmljWUTkPhpiXjfv6-g)
cgstudio
Duct TapeVery Detailed Duct Tape. ...The Model is Low Poly, and perfect for any game environments, such as fps horror, MMO, Survival, etc.It also fit perfect as a Item pickup in many game genresModel is unwrapped, and UV Mapped using Photoshop.Diffuse,...
thingiverse
This duct tape holder prints without needing supports or rafts, is flexible enough to let the duct tape in through the flared edges, but is sturdy enough to not let it fall out even if held on its side. You may also try to use it as a filament holder...