duct tape roll holder 3d models
398623 3d models found related to duct tape roll holder.youmagine
A pencil holder for my workbench designed to hold either 2 rolls of duct tape or that roll of kapton tape that I don't use any more but can't bear to throw away. I've been using that kapton roll as a makeshift pencil holder for a while now, but it's...
thingiverse
this is a tape holdet to put near your 3d printer so you can replace the painters tape easely
thingiverse
Designed a tape holder for holding rolls of tape for rod building. ... These are designed to hold two rolls of tape up to 1" in width.
thingiverse
This thing is made to replace the roll bearing in a Tesa Tape holder.
thingiverse
This is a simple holder for a Tape Roll. You simply need to screw it to a vertical surface. ... You can use it for other purposes obviously.
thingiverse
Roll holder for 25.5 mm (diameter) tape rolls. I adjusted it a bit and made the two sticks on the side a bit thicker and shorter to fit the needs of this particular tape dispenser. The sticks are 5 mm long and 7.8 mm thick. ...In total it's 33,5 mm...
thingiverse
After having printed a bunch of tape roll holders by ctheroux ( https://www.thingiverse.com/thing:295690 ), I needed something to hold smaller rolls also. So I designed a simple holder, based loosely on ctheroux's design. ... .sldpart (SolidWorks...
prusaprinters
This is a simple holder for a Tape Roll. You simply need to screw it to a vertical surface. ...You can use it for other purposes obviously.</p>
thingiverse
My blue tape roll was always getting in the way so I got out one of these spool holders from my scrap bucket and repurposed it. As shown in one of the photos, this arm can hold a roll of tape up to 3 inches wide. I use a two inch wide roll for my...
thingiverse
You can use 1x big roll, or even 2x small rolls next to eachother (example: if you need different colors) HOW TO: 1st option: Add 7 strong magnets (10x4mm) in the clip and holder. Alternate the + and - (see picture)! Glue the caps on top. Now you can...
prusaprinters
This is a simple holder for a Tape Roll. This design is much more robust than the previous one (<a href="https://www.thingiverse.com/thing:154458">http://www.thingiverse.com/thing:154458</a>).</p><p>You simply need to screw it to a vertical surface.
thingiverse
This is a simple holder for a Tape Roll. This design is much more robust than the previous one (http://www.thingiverse.com/thing:154458). You simply need to screw it to a vertical surface. ...You can use it for other purposes obviously.
thingiverse
I'm constantly picking this roll of tape up and moving it around, so I thought I'd give it a better home, and designed this holder. The first draft of the design was sort of a fixed bar that just went straight out. I didn't even bother printing...
thingiverse
Replacement tape dispenser spinny center piece. Works for standard rolls. I split the model and print in two halves then superglue together. ... Made in both PETG and PLA Roughly 16 minutes to print, about $0.20 of plastic.
thingiverse
I use blue painters tape on a glass bed for all of my printing and I wanted some place to put the roll of tape so it would be out of the way. This has 2 slot for the arms to hold the 1" and 2" rolls. Arms are super glued in and in my case are able to...
thingiverse
A replacement part for that little thing in tape dispensers that the roll of tape is held on. Instructions There are two files. They are the same but just a different orientation. ...Personally, I think...
thingiverse
Replacement for Scotch and similar size tape dispensers. ... We lost one in our office, and rather than buy a new one it was easy enough to design and print. Can print in 1 piece with supports, or as separate holder and pin, then glue them together.
thingiverse
... ID of tape reals, meaning it haves to flex to fit inside, does so pretty easily, and will not shift at all! Hope it helps someone else who has had the same occur, such to throw out such a heavy tape dispenser just because of a little plastic pin!
thingiverse
Simply another Duct Tape Holder. Made for 50mm wide and 70mm round Tape. ... Screwed to my cabinet with two 12mm screws.
thingiverse
http://www.thingiverse.com/apps/customizer/run?thing_id=691124 Instructions Using the following options: wallthickness = 1.2 outer_diameter = 122 text_font = orbitron.dxf text_space_factor = 1.1 dot_diameter = 2.4 height = 520 inner_wallthickness = 2...
thingiverse
This duct tape holder prints without needing supports or rafts, is flexible enough to let the duct tape in through the flared edges, but is sturdy enough to not let it fall out even if held on its side. You may also try to use it as a filament holder...
prusaprinters
Holder for duct tapes. You can store small ones inside of big ones.</p> <h3>Print instructions</h3><p>Use thin layers for precise threads (or use adaptive layer heights). ...Print both part one after another to achieve better visual result.</p>
thingiverse
It's time to trick out your workshop, garage or office, hang your duct tape in style! It might just be one of the most respected tools in your arsenal, make sure you treat it as such. The model Thing comes in both tape dimensions 48mm / 51mm...
thingiverse
You will also need an 8 mm rod or tube. ...Length is free a suitable tape diameter of about 85 to 130 mm. Desinged tinkecad. ... Engineering jobs from Finland and google translations.
thingiverse
Well title is self explanatory, I believe No supports. ...Single screw. Because the screw is higher then the roller center of gravity, holder doesn't tend to rotate Basic Holder width = 51mm Dual Holder width = 81mm
thingiverse
Wall mounted tape roll holder with BLUE or DUCK cover. ...This is designed to be printed as 2 pieces and glues together.
thingiverse
This is simply to hold a tape roll for an adding machine.