duplicator 4s 3d models

For Wanhao Duplicator 4s hood

I redesign this Replicator 2X tool holder for a Duplicator 4S for my tools. ...Version 6 : add place holder for lego tool.

Fit into holes in the corners, I needed to file a little on the two inward corners, because my Duplicator 4s failed to create a sharp angle (I'm still a novice) I used ABS to maintain temperature stability Print Settings Rafts: No Supports: No...

Simple uprage to keep "hood" of your Duplicator 4S from relocating due to vibrations. Just snap it into corner holes of top cover and place hood above. Place with short side facing front of Duplicator. ...If you have ideas how to make it better, please...

Door stop for the Duplicator 4S.

Doorstop to Wanhao Duplicator 4S. ...Print Settings Rafts: Doesn't Matter Supports: Yes ...

Print Settings Printer: Wanhao Duplicator 4S Rafts: No Supports: No Resolution: 0.27mm Infill: 10% Notes: Ordnung ist alles! :-) Post-Printing If you have an Wanhao Duplicator 4S / 4X / 4, you can use the right plate screws to attach it to the right...

Blog post: https://juhannuskameli.wordpress.com/2021/10/13/marlin-firmware-for-wanhao-duplicator-4s-3d-printer/ Code can be found from github and commits are welcome: https://github.com/user176176/Marlin/tree/Wanhao_Duplicator_4S Notes: - Steps...

This is a simple device for keeping the door on a Wanhao Duplicator 4S open. ... It should also work on a MakerBot Replicator 2x as they are basically the same.

Remixed from http://www.thingiverse.com/thing:496298 so it will fit the Duplicator 4s. The plate can be installed to additonaly secure the bearing. ... You will need a bearing: 5x11x4 mm Instructions...

... In the spirit of Game of Thrones, I gave it a name :) Print Settings Printer: Wanhao Duplicator 4S Rafts: Doesn't Matter Supports: Doesn't Matter Resolution: 0.10mm Infill: 15% Notes: I printed mine in somewhat high to keep it rigid as possible.

... to securely attach it to the printer. ...This little corner piece solves that. Print time for 4 pieces was 58 minutes and it used about 3 meters of filament. Print Settings Printer: Wanhao Duplicator 4S Rafts: No Supports: No Resolution: 200 Infill: 15

A little magnetic door stop for the Duplicator 4S. It uses two 5x3mm round neodymium magnets which are for the door attachment (glued on) The chassis section has a 5mm pin which you need to locate into a 5mm hole you need to drill. It also uses 4...

... ... I modified this to work on the Wanhao Duplicator 4s. ... Instructions I use PLA and yellow Octave ABS, both seem to work well, I used a raft because I can't seem to get it to stick with out one.

Spool holder for Wanhao Duplicator 4S

This is a replacement for the original fragile one for the MK10 extruder on Duplicator 4s.

... Print Settings Printer: Wanhao Duplicator 4s Rafts: Yes Supports: No Resolution: 0.2 Infill: 20% Notes: I had additionally parameters with PLA: 60 degrees Celsius bed temp 230 degrees Celsius nozzle temp closed case Post-Printing Close-up Overview

... at 50 C Build with small hole up and I used a cooling fan to help with the large hole bridging. It may not be necessary. Parts need (2) 18mm Diameter X 5mm Thick magnets (1) spare nuts and (1) machine screws from the Duplicator 4S hardware bag.

When using a front-mounted PLA fan with the Wanhao Duplicator 4S 3D printer, there is a chance that it will hit the door covering the front of the machine. ...To solve this we designed a frame that will offset the door by 20mm and allow for a fan to be...

Wed 06.04.2014 : New Version 4 for a stronger one. ...Thu 31.03.2016 : Version 3 for a best print Fri 18.03.2016 : Version 2 remixed from http://www.thingiverse.com/thing:1104116 Functionalities for DUPLICATOR 4S : Scotch holder Door lock

... ... I used 10% infill PLA with 3 shells at 200 C extruder temp and 50 C Bed Temp. It has been configured for the Duplicator 4S Build plate. ... Note: If using the stl files 2 sets of winders are required, the thing file has all required parts.

Here a remake of myself for the Wanhao Duplicator 4s. Print Settings Printer: Wanhao Duplicator 4s Rafts: Yes Supports: No Resolution: 0.2 Infill: 20% Notes: I had additionally parameters with PLA: * 60 degrees Celsius bed temp * 230 degrees...

Re-arranged part for Duplicator 4S build plate. I have included the .thing file for the 5 plates, the individual part files in the .zip, and meshmixer file where is separated the parts. I just built all 5 plate and used 50C build plate temp on the...

When using a front-mounted PLA fan with the Wanhao Duplicator 4S 3D printer, there is a chance that it will hit the door covering the front of the machine. To solve this we designed a frame that will offset the door by 20mm and allow for a fan to...

When using a front-mounted PLA fan with the Wanhao Duplicator 4S 3D printer, there is a chance that it will hit the door covering the front of the machine. To solve this we designed a frame that will offset the door by 20mm and allow for a fan to...

A SD Card Guide & Blocker Version 2 for the Duplicator 4S. This is to prevent accidental insert of the SD Card into the open areas around the reader and the drop into the electronics housing area. Snap in fit. Version 3 Final Version 1) added...

Just tried to modified Basic Hinge for Wanhao Duplicator 4S Cover made by b03tz Source ---> https://www.thingiverse.com/thing:2415736 Bolt Size : Head 8mm Tail 3mm *Print it Standing Up *Use Support My slice setting : Skirt Skirt Layer : 1 Skirt...

Modified so it keeps the 4s door open. Place over the centre nut to support. ...Bit rough round edges - if anybody knows sketchup better plse remix!

Filament tube holder for Wanhao Duplicator S4. ...Print Settings Rafts: No Supports: No ...

I was fed up with stashing my hex keys, spanner and scraper in the body of my printer so with 2 nuts n bolts being nicely placed at the top of the window i made this holes for hex keys Box for spare screws bits n pieces Slot for a scraper Front...