duplicator mod 3d models
42616 3d models found related to duplicator mod.thingiverse
This is a mod to extend the Y axis of the Wanhao Duplicator i3 120mm. You will need: -A longer GT2 Belt (24cm longer) -2 8mm x 500mm steel rods -6 M3 size screws (any length will do) -Change the Max Y in EEPROM to 320 -Cut the two tiewraps that...
thingiverse
... cut it to fit the new modded extruder assembly. After this mod my Duplicator works just as I would expect from a good 3D printer. ...As a bonus, I could push more acceleration out of my printer because now there is no second stepper to move!
thingiverse
This is actually a modification of an exelent design, found on a page by SmartBlug. Since it lifts the fan out of the box, it's possible to use a 60mm fan. A 40mm fan typically delivers 12m3/h, while a 60mm fan gives you more than 30m3/h. (Thats in...
thingiverse
Strengthening of the hull 3D printer Wanhao duplicator i3. All bolt holes bore with the details of the printer. In some places, drilled extra bolt holes. All metal parts of the printer left in their places. Gain cut out of plywood 10mm thick. For...
thingiverse
rimozione del fastidioso rumore del sistema di spinta bodwen Removing annoying noise from the bodwen boost system materiale 4 molle lunghe tubi in carbonio o similare material 4 long springs Carbon or similar pipes risultato un altro...
prusaprinters
It requires a lot of 3 mm bolts from 12 mm up to 20 mm in thread length, (2) 4 mm bolts that are 20 mm long, and (2) 2 mm bolts that are 12 mm long.Assembly Photo Galleries00 Frame System Overview - http://imgur.com/a/nDK1501 Frame -...
thingiverse
This should also be compatible with all the clones of the Duplicator i3. Print 2 of the brackets to balance the load. There is .1mm clearance, so you'll get a snug fit on the boxes when you push them on, and it's very stable. ...I left plenty of...
thingiverse
You need 2x410mm linear rods and 2 long or 4 short linear bearings. The original holes fits perfect so it is not necessary to make others. ...
thingiverse
Centers the fan more directly over the hot end. ...Use screws which are 2mm longer than factory.
youmagine
I printed this thing:http://www.thingiverse.com/thing:916707 and found due to greater shrinkage of the feet than the bracket that they wouldn't hold: the foot slid up the thread with any pressure. However, it turned out that a steel M8 bolt fit the...
thingiverse
This is a Mod I made for my Cocoon Create 2.1 to replicate the compact nature of the following model where the control box is consolidated into the base. This is an Advanced mod and must only be used by users with an advanced knowledge of their...
thingiverse
a simple design to activate your z-height stop at a lower bed height, to allow easy fitment of a glass bed. simply scale the z height in your slicer to your requirements and place the spacer around the bottom of your z screw pillar. the thing is 3mm...
pinshape
Wanhao Duplicator 6 Facebook group https://www.facebook.com/groups/1568631046795094/ Wanhao Duplicator I3 Facebook group https://www.facebook.com/groups/WanhaoDi3/Print SettingsPrinter: WanhaoRafts: Doesn't MatterSupports: NoResolution: 200Infill:...
thingiverse
Wanhao Duplicator 6 Facebook grouphttps://www.facebook.com/groups/1568631046795094/ Wanhao Duplicator I3 Facebook grouphttps://www.facebook.com/groups/WanhaoDi3/ Print Settings Printer: Wanhao Rafts: Doesn't Matter Supports: No Resolution: 200...
thingiverse
very similar to the original. just modified slightly to be able to print easier. ... Print solid in ABS to handle the heat, supports and .1mm Layer height.
thingiverse
Hey Guys this is another mod for Wanhao Duplicator I3, Maker Select, and Cocoon Create 3D Printers. this time its a filament guide. i have found this very helpful to direct the filament where it needs to go. No non 3D printer parts are needed, your...
thingiverse
Printing soft TPE filament was a challenge on my Wanhao Duplicator i3. The elastic filament would escape the filament channel and stop extruding. This replacement body has a tight fitting channel that actually mates with the idler wheel, leaving no...
thingiverse
This is a remix of the top cover from the Z-Axis Mod for Wanhao i3 Duplicator by ShadowWeaver2067 and Wanhao Duplicator i3 Filament Guide Tube Adapter by Drazen. Print one of Drazen's guides filguide4mmV2.stl for the extruder, and make this for the...
thingiverse
### Wanhao Duplicator i3 Plus Y-belt Pulley Mod 2020 REVISED VERSION Here are my own 2020 revised version of a y-axis pulley stabilizer for the Wanhao Duplicator i3 Plus. I've used in the past already some existing models, though i never was 100%...
thingiverse
Print Settings Printer Brand: Wanhao Printer: Wanhao Duplicator i3 V2 Rafts: No Supports: No Resolution: Does not matter as long as it will print nicely Infill: 100% Notes: 100% infill is required. ...I mean these are used to level your print bed, that...
thingiverse
Print Settings Printer: Duplicator I3 PLUS Notes: I did not use supports/rafts and I also used lower quality settings with a fast print speed and a layer height of 0.3 mm (suggested 80% infill which for this model is irrelevant depending on how thick...
thingiverse
The kid really needs your support, and his goal is to reach 500 subscribers:http://goo.gl/ELT7ii The original gantry feet by TRAVMO weren't sized correctly for the Azza Z brace mod, which is the most popular of the Z brace mods. The Azza Z brace mod...
thingiverse
This is a x-carriage for the Wanhao i3, i have spent a long time designing this and printed many test pieces to get it as clean and light as possible, The reason for designing and printing this is the whole new carriage with all accessories weights...
thingiverse
I had a bunch of parts for the openbuilds style mini v gantries hanging around, so I decided to mod them in. You can buy from openbuilds themselves, or go with cheap chinese clones from aliexpress etc, but bear in mind the bearings on the latter are...
thingiverse
I rearranged the fans so that they're on the top instead of having the bottom one blowing directly on the psu.
thingiverse
ORIGINAL FILES: http://www.thingiverse.com/thing:921948 TO FIT ON MONOPRICE MAKER SELECT PLUS SELECT THE "Maker_Select_duplicator_i3_PLUS_Z-Brace_mod.stl" THIS ENTIRE FILE WILL PRINT ON THE BED (IT WILL FIT WITH NO CRAMPED PARTS) IN THE COMMENTS I...
thingiverse
This is a remix of Herman_PID's filament guide remix here https://www.thingiverse.com/thing:904146 and Drazen's PTFE tube mount here https://www.thingiverse.com/thing:877258 I noticed there were no guides and mounts for this mod that worked with v2.1...
pinshape
SummaryWanhao duplicator I3 mod for bowden. 6mm hole for threaded bowden attachment from a cheap e3d Still testing this! ...My youtube channel is at https://www.youtube.com/channel/UCbktKakstfc68xXnrT_Olgg/videos Join the facebook group at...
thingiverse
Wanhao duplicator I3 mod for bowden. 6mm hole for threaded bowden attachment from a cheap e3d Still testing this! ...My youtube channel is athttps://www.youtube.com/channel/UCbktKakstfc68xXnrT_Olgg/videos Join the facebook group...