dw611 3d models

28 3d models found related to dw611.
Gatton CNC DW611 Spacer
Gatton CNC DW611 Spacer
thingiverse

Gatton CNC Dewalt DW611 spacer. ...I made these spacers to quickly allow the use of the DW611 router. ...I have a bunch of 1/8" bit i need to use and i have a collet for this router.

dw611 dust Shoe
dw611 dust Shoe
thingiverse

Dust collector shoe for Dewalt DW611 trim router on cnc router setup Still needs recesses added for 3mm mounting hardware as the plastic cannot hold the threads enough to get the required amount of pressure for a good fit.

dw611 dust Shoe
dw611 dust Shoe
pinshape

Dust collector shoe for Dewalt DW611 trim router on cnc router setup Still needs recesses added for 3mm mounting hardware as the plastic cannot hold the threads enough to get the required amount of pressure for a good fit.

Dewalt DW611 Dust Boot
Dewalt DW611 Dust Boot
grabcad

This dust boot design, created in Fusion 360, was inspired by the CNCRouterParts open source design and was modeled specifically for the Dewalt DW611 trim router, although it should work with other small routers with a diameter of 2.7". The 2.5"...

Dewalt DW611 Dust Shoe
Dewalt DW611 Dust Shoe
prusaprinters

This is a dust shoe for the Dewalt DW611 router. The screws to attach to the lower base are 1/4-20" x 5/8" SHCS Long These are the magnets used, 10mm x 3mm and hot glued into the upper shoe....

Dewalt DW611 Dust Shoe
Dewalt DW611 Dust Shoe
thingiverse

This is a dust shoe for the Dewalt DW611 router. The screws to attach to the lower base are 1/4-20" x 5/8" SHCS Long These are the magnets used, 10mm x 3mm and hot glued into the upper shoe. ...

Neje 40640 Dewalt DW611 Mount
Neje 40640 Dewalt DW611 Mount
prusaprinters

I have the DW611 router and base installed on my V1 Low Rider (version one). This lets me take the router out, put the laser diode in, and then just add wiring. It also still fits [dkj4linux's hose/nozzle](https://www.thingiverse.com/thing:5073015)...

Mostly Printed CNC D26204/DW611 holder (mpcnc)
Mostly Printed CNC D26204/DW611 holder (mpcnc)
thingiverse

I made this one for my DeWalt D26204 router but i believe it will fit the DW611. (let me know if you tested it) Or a 69mm router housing. For my mount i used 50% infill 4 shells and 0.2mm layers (22hr) Its bolted to the 2 vertical pipes with 4 M6...

Dewalt DW611 Super-PID Tachometer Holder
Dewalt DW611 Super-PID Tachometer Holder
thingiverse

I use a DeWalt DW611 Router as a spindle on my Shapeoko 3, and also use a Super-PID controller to control the speed of the router. The Super-PID controller requires an IR Tachometer to be mounted in such a way to see the spindle, which has to be...

Dewalt DW611 Super-PID Tachometer Holder
Dewalt DW611 Super-PID Tachometer Holder
prusaprinters

I use a DeWalt DW611 Router as a spindle on my Shapeoko 3, and also use a Super-PID controller to control the speed of the router. The Super-PID controller requires an IR Tachometer to be mounted in such a way to see the spindle, which has to be...

DW611 Shapeoko Mount
DW611 Shapeoko Mount
thingiverse

Custom spindle mount for Dewalt DW 611

DW611 Base to Plotter
DW611 Base to Plotter
thingiverse

Holds a pen, allowing for it to rise when pressed into paper. Useful for plotting on a CNC machine. ... Based on the work of barry99705, but I can't remember where his design ended and this began.

35 mm adapter for Dewalt DW611 Dust Attachment
35 mm adapter for Dewalt DW611 Dust Attachment
thingiverse

I made this to adapt a Bosch 35 mm VAC005 hose my Dewalt DW611 router dust port. ...Print Settings Printer Brand: Printrbot Printer: ...

Shim for Dewalt DW611 in Openbuilds Router mount
Shim for Dewalt DW611 in Openbuilds Router mount
thingiverse

While the nominal diameters are 71mm for the Colt and 69mm for the DW611, I found that with the vagaries of my printer (prusa i3 derivative), I needed .5 mm gap to make it actually fit. There is one shim that leaves 0.25mm gap that that was too small...

Low Leverage DW611 Spindle mount for Shapeoko 2
Low Leverage DW611 Spindle mount for Shapeoko 2
pinshape

For those looking for a complete spindle mount and dust collection solution, my bolt on DW611 Dust collector plate is also compatible with both Z axis configurations when used with this spindle mount. ... Requires: 4 - M5x15mm Cap head bolts,3 -...

Bolt on DW611 Dust Collector Upper with built in deflector
Bolt on DW611 Dust Collector Upper with built in deflector
pinshape

Fully compatible with my Low Leverage DW611 Spindle mount for Shapeoko 2 Now includes Brush plate! Requires: 1 - Vacuum hose adapter & 4 - M5 bolts with nuts 2 - pan head wood screws about 25mm long (to replace factory screws that hold...

LowRider V2 - DW611 Pen Holder
LowRider V2 - DW611 Pen Holder
thingiverse

This is a pen holder that snaps into the dewalt router plate that is standard for the low rider V2. Just pull out the router (or retract it if you have a short pen) and snap in the disc from underneath. Compatible with my Z-Probe so it will know...

Shapeoko DW611 Dust Collector Shoe
Shapeoko DW611 Dust Collector Shoe
pinshape

UPDATE 6/12/2016: Added 2.5" hose adapter.  This will require the bolts to be inserted from the bottom, and up into the flange adapter.  It will also require an additional 4 M5 nuts to complete the build. UPDATE: I have updated the...

LowRider V2 - DW611 Pen Holder
LowRider V2 - DW611 Pen Holder
prusaprinters

<p>This is a pen holder that snaps into the dewalt router plate that is standard for the low rider V2. Just pull out the router (or retract it if you have a short pen) and snap in the disc from underneath. ...Compatible with my Z-Probe so it will know...

ShopVac hose mount
ShopVac hose mount
thingiverse

For use in combination with DW611 Router Dust collector

1 1/4" vac hose coupler for Dust Collector
1 1/4" vac hose coupler for Dust Collector
pinshape

... shop vac hose. ... This piece bolts to the DW611 dust boot bolt on dust collector foot/air deflector.   This piece requires minimal support and should be printed at .25 or less layer height.  PLA or ABS should be fine for printing this object. ... 

X-Carve with Quiet Spindle - JTech Laser Middle Mount
X-Carve with Quiet Spindle - JTech Laser Middle Mount
thingiverse

See the Mounting Options for **Dewalt 611** Spindle: [Front DW611 Mount](https://www.thingiverse.com/thing:2542291) [Side DW611 Mount](https://www.thingiverse.com/thing:2542285) ####More Info#### **More about Lasers** [JTech...

Dewalt 611 Air diverter
Dewalt 611 Air diverter
cults3d

This is used to change the air flow when using the Dewalt DW611 router with a CNC machine. The only mount I have tested compatibility with is the X-carve. I have not tried to print the "with lights" one because the lamps mess up my webcam monitor...

Festool / Bosch Vacuum House Anchor and Adaptor for Improbable Construct dust shoe.
Festool / Bosch Vacuum House Anchor and Adaptor for Improbable Construct dust shoe.
thingiverse

I bought a used Shapeoko 3 which came to me with an [Improbable Construct dust shoe](https://improbableconstruct.com/collections/dust-shoes/products/dust-shoe-diverter-for-dw611) on the DeWalt 611 router. This didn't fit the hose on my Festool dust...

X-Carve with Quiet Spindle - JTech Laser Middle Mount
X-Carve with Quiet Spindle - JTech Laser Middle Mount
prusaprinters

The beam focused perfectly within the factory recommended distance by fine tuning the Z-Axis. See the Mounting Options forDewalt 611 Spindle: Front DW611 Mount Side DW611 Mount More Info More about Lasers JTech Photonics More about X-Carve CNC...

CNC Tool Mill Holder and Clamp Drawer
CNC Tool Mill Holder and Clamp Drawer
thingiverse

... add some bolts to stop the drawers from sliding all the way out. Make sure to print the mill drawer with supports to the slots on the sides keep their shape. Mill drawer holds 1/8" and 1/4" shank mills and collets for the dewalt DW611 router.

CNC Tool Mill Holder and Clamp Drawer
CNC Tool Mill Holder and Clamp Drawer
prusaprinters

There are bolt holes in the drawer brackets so you can add some bolts to stop the drawers from sliding all the way out. Make sure to print the mill drawer with supports to the slots on the sides keep their shape. Mill drawer holds 1/8" and 1/4" shank...