dye i4 gopro mount 3d models
356767 3d models found related to dye i4 gopro mount.
thingiverse
This is a clip-in GoPro Mount for Dye i4 paintball mask. Made a very flat and solid version, inspired by "Dye i5 Top Camera Mount by ofek256" https://www.thingiverse.com/thing:3286019. ... The normal GoPro screws wont fit, so you will need a normal M5...
thingiverse
Sturdy GoPro mount for your dye i4 paintball mask. You will need two 1/8in nuts and bolts to put this together, as well as the nut and bolt from an existing GoPro mount. ...How I Designed This SolidWorks 2014
pinshape
I decided to design this mount because the only other top mount gopro mounts for the dye i4 masks were $15-$30 dollars USD so i'd thought i'd make a simpler more affordable version. The hardware i used to mount this on my mask was EVERBILT nylon...
thingiverse
Beta mount for Go-Pro Design Credit goes to "SecretObsesion" for the base mount.
thingiverse
Description Been playing paintball with my Contour+2 and wanted to have a proper mount for my Dye i4 Mask. There are a few holes in the bottom of the "lip" that will allow you to use small zip-ties to affix it to the mask. I've rounded out the back...
pinshape
Description Been playing paintball with my Contour+2 and wanted to have a proper mount for my Dye i4 Mask. There are a few holes in the bottom of the "lip" that will allow you to use small zip-ties to affix it to the mask. I've rounded out the back...
thingiverse
Walkie/Radio system for dye i4 with built-in PTT System is testede and Works very well, very good sound both as sender and receiver, Boom and wiring diagram is attached to this thread, plus some pictures of how it comes together BOM Pin Header (...
thingiverse
Use an m5 thread screw and bolt for this kind of mount instead of gopro screw because it wont fit. I built it like this so it wont snap . update: So as of today August 9, 2018 I'm still using it without any problems. I start using this since feb...
thingiverse
I've searched for a GoPro-Mount for my Dye Proto FS Fullface-Mask, but didn't found something, so I created a mount by myself. If you did a print: Please post a "i've made one" and share your experience on the comments-tab! and if you like my...
thingiverse
this is a mount that was made for a tronxy x3 that I modified for an i4 it is e3d v6. I have not test fitted it yet as I am awaiting my e3d hot end. if you print it let me know any mods that need to be done. needs to be printed with support touching...
thingiverse
This is an adapter so you can mount a camera on the top of your dye i5 (maybe i4 too). The pictured design is a little out of date, I rounded and smoothed out the whole model. You will need a short M4 screw along with a nut and a GoPro mounting...
prusaprinters
Adapter to mount a gopro on top of your dye i5 (maybe i4 too).The pictured design is a little out of date, I rounded and smoothed out the whole model. You will need a short M4 screw along with a nut and a GoPro mounting screw and nut...
thingiverse
https://www.thingiverse.com/thing:4441076 presented a thumb screw to replace the wing nut on the front-left corner of the BIBO bed. It is too wide for the other two positions. I have created a smaller version to fit the right-front corner and the...
thingiverse
This is a wall mount bracket for the Intellicharger NEW i4. It allows easy removal and installation of the charger. ...The bracket not secure enough for moving or vibrating environments.
thingiverse
This is the mounting bracket for the LJ12A3-4-Z/BX inductive sensor for the Prusa i4. Printed at 0.3 layer height and 20% infill. Hope it works for you!! ...:)
myminifactory
This is a wall mount bracket for the Intellicharger NEW i4. It allows easy removal and installation of the charger. ...The bracket not secure enough for moving or vibrating environments.
thingiverse
I made 3 models for the Prusa i4 hotend fan,and one for radial fan 50x50mm, with adjustable height mounting. I use the "Medium model" this Work for me. I also use the BlackSilent Fan XM-2 - 40mm from Caseking.de this models give a medium Wind. ...If you...
thingiverse
you will also use tnuts as they should fit in the holes for the mounting to the x carriage. this is just a start as I am still waiting for my e3d hotend to show. of you print it please give me feedback and let me know about the fitment and hotend...
thingiverse
the part of the printer on which the engine of the extruder of the cooling system is supported; fuser, etc. ...drew for alteration.
thingiverse
I got a new DYE I5 Mask and adjusted my Contour GPS mount to use the Camera mount in the mask. ... Parts Needed: 1/4-20 Jamb Nut - Install in the nut trap inside the mount M3 Screw 25mm Long - For Clamping M3 Nut - For Clamping
thingiverse
#UPDATE 2018-11-04 UBL (Universal Bed Leveling) https://www.youtube.com/watch?v=PTEQZEGhKoM - (Russian Guide) #How To Extended for this thing https://www.thingiverse.com/thing:2182105 Mount for geeetech.com 3DTouch sensor for Prusa i4 3DTouch Sensor...