dyno obt 3d models
140 3d models found related to dyno obt.thingiverse
Customized version of https://www.thingiverse.com/thing:739573 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=739573
thingiverse
Customized version of https://www.thingiverse.com/thing:739573 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=739573
grabcad
a compact moped dyno I made myself, also suitable for light motorcycles. ...the rotor is out of a big electric motor (+-220kg in total with the additional 50kg flywheel)
cults3d
A basic Dyno for your 1/64 scale cars .rollers roll .Print dyno 1 piece then rollers and end caps .you can us a hw axel and cut it in half and place it at each end and a touch of glue so they don't come out , and then glue the end caps on .
cults3d
Cute little dyno child toy, ore you can use as a key fob, keychain, the eyes are united in a single hole, so you can hang it from his eyes.
cults3d
https://www.youtube.com/watch?v=p8GeBThoJ8M https://www.youtube.com/watch?v=d-Pk1FI84oQ BUILDING SUPRA 3D PRINTED BODY https://www.youtube.com/watch?v=arcTKhUyKuE dyno 4WD for rc cars, EACH WHEEL NEEDS 2 SKATEBOARD BEARING you will need four 13mm...
thingiverse
https://www.youtube.com/watch?v=p8GeBThoJ8M https://www.youtube.com/watch?v=d-Pk1FI84oQ BUILDING SUPRA 3D PRINTED BODY https://www.youtube.com/watch?v=arcTKhUyKuE dyno 4WD for rc cars, EACH WHEEL NEEDS 2 SKATEBOARD BEARING you will need four 13mm...
thingiverse
I designed this model chassis dyno just for use with dioramas, scale garage, photoshoots, and what ever else you might need a model chassis dyno for the scale it comes in is a little smaller than 1/64 and many 1/64 vehicles won't fit on it so you...
grabcad
Benchtable extension stand foot with switch and I/O-Panel With this Benchtable extension, you can easily and quickly build a show computer from the BC1 for daily use, not just for testing.
cults3d
Dyno-stand for 1/64 service diorama. Modular design, "drums" can rotate. ... You also can use this kit for another scale.
pinshape
DYNO TEST designed for 1:64 scale .2 mm layer height 20% infill no support need it the assembly its to easy you will need a few paper clips to install de rollers and some contact glue to attach the Floor to de dyno to finsich the installation check...
thingiverse
This is a Electronic Board Cover for the miniPRO Flywheel Unit used on the Motor & Chassis Dyno. Part No. 08090001MD101 = Version 1.0 Part No. 08090001MD102 = Version 2.0 P.S. ...Part No is located below the reset button
grabcad
After many weeks of troubleshooting and diagnosing problems, I've finally finished my first iteration of the RC Motor Dyno! I say first iteration because I'm almost certain I will want to create a new one in the not so distant future as I already...
thingiverse
rolling chassis dyno style stand i made to test squat on my RC car, this project requires two roller from mcmastercarr.com holes will need to be threaded to bolt together, these are long parts so you might need to slice to fit your printer. ... ...
thingiverse
After many weeks of troubleshooting and diagnosing problems, I've finally finished my first iteration of the RC Motor Dyno! I say first iteration because I'm almost certain I will want to create a new one in the not so distant future as I already...
thingiverse
# Micro UAV propeller meter Features: - thrust and torque readings - voltage and amps readings - step response analysis - arduino nano based pcb - using 3 load cells (12.7x12.7x80 up to 5 kg) - HX711 modules with 80 Hz update rate -...