e flite blade mqx quadrotor 3d models

The ideal rear fins (Wings) for the E-flite/FMS F/A-18D 80mm EDF jet fuselage mounted AIM-120 are precisely replicated here. ...The standard issue rear fins are merely the forward fins attached to the aft section of the fuselage missile body, but these...

I designed this specifically for attaching my Castle 30A BEC and E-flite 60A ESC on the rear floor of my Scale Hull (SH). ...You'll find separate files for each component, including the ESC and BEC mounts without the platform, that you can download and...

I used Tinkercad to modified the adapter created by Shadowvfx to fit my E-Flite 70mm Habu SS with the BL Outrunner Motor: 2847-2400Kv. ... I basically created a new ring at the top and slots for the 6 fins, the adapter is intended to be glued to the fan...

Port and starboard tail moldings for E-flite SU 30. This replaces the foam moldings with more realistic representations of what's on the actual aircraft. 1 file for port tail, 1 file for starboard tail, and one file for horizontal strakes that run...

Motor cover for the E-Flite Carbon-Z Cub SS 2.1m PNP. In replacement of the expanded polystyrene cover .(15 Grams) It uses the same fasteners as the original. The outer shape is slightly modified. ... By reducing the filling to the max I arrive at...

... you can decide that destiny. High poly model done in Zbrush, projected to be in 32mm - Base 32mm (Pre-supported and tested). Manual to scale your miniatures. Can be print bigger, ideal for resin printers, supports Included. ...I hope you like it!

... you can decide that destiny. High poly model done in Zbrush, projected to be in 32mm - Base 32mm (Pre-supported and tested). Manual to scale your miniatures. Can be print bigger, ideal for resin printers, supports Included. ...I hope you like it!

EN: Repacement parts for E-Flite F-18 80mm ducted fan This is a more realistic AIM-9 Sidewinder Fit perfectly in the original support No glue needed (except if you have to print splitted parts), just print it and plug it to your plane For a better...

A quadrotor model built upon the Syma X1 had a large shroud that was 3D printed but proved too heavy for flight. ...A lighter, smaller shroud allowed for flight, albeit with reduced speed.

Here is a simple wall mount setup for the E-Flite F-16 Falcon (EFL9875). The holder is designed specifically for a 50 mm tire. The label easily fits into the top of the holder and can be left in place if desired. The sides are taller than the...

This is a specialized trunion specifically crafted for use with an E-Flite 10 to 15 size nose gear retract. Designed for seamless integration with a press-in expansion nut (available at http://www.mcmaster.com/#94510a040/=10g8hmq), it provides a snug...

Landing gear mounting clamps for the E-flite Twin Otter RC aircraft. Printed this for my Dad because he broke his clamps during a hard landing. He said the only way to get new ones is to order a whole new set of landing gear. I designed this in...

This is a sturdy engine bracket designed specifically for the e-flite Micro Mustang P51 D, a compact 550mm plane equipped with AS3X stabilization technology. Note that this bracket serves as a support for the plane's front structure, unlike the...

This is the complete set of missiles/launcher/stores-pylon for the E-Flite 80mm F-18D The LAU-115 attaches firmly to the wing pylons via powerful magnets that can be sourced separately, and are keyed into position so they remain perfectly straight. I...

STEP files for the E-flite EFLG330 Tricycle 25-46 landing gear set. This covers the regular 90-degree main gear set as well. These are dimensionally accurate on the exterior dimensions, mounting holes, wire locations, pivot points, etc. The interior...

STEP files for the E-flite EFLG330 Tricycle 25-46 landing gear set. This covers the regular 90-degree main gear set as well. These are dimensionally accurate on the exterior dimensions, mounting holes, wire locations, pivot points, etc. The interior...

I designed this custom support specifically for my E-flite Opterra FPV wing. When I'm preparing to land, I appreciate being able to glance at the side of the plane. The front of the support features a hole for cable management. All you need to do is...

This is a camera mount for the E-Flite 1.2m P-51D "June Night". Simply slide them on where the drop tanks attach. They are designed for the Replay XD 1080, which are a bit long in the tooth now, but I happen to have a few. They're also a bit heavy...

This is my 3rd version of landing gear for the E-flite Opterra. Version 1 and 2 used double sided tape to attach to the unmodified keel of the plane. On a semi-hard landing I managed to break the plastic keel instead of having the tape come loose....

... This is a shroud/nacelle for the E-flite 28mm EDF unit, designed to bring more excitement to your discus launch glider. The tiny 28mm screaming ducted fan seemed like the ideal choice to achieve this! Check out the link below for the matched item.

This thing covers the inner vertical stabilizer fin slots for the E-flite Opterra 2M when flying with only the outer stabilizers. They are secured by the carbon spar as the original fins. My prototypes on the pics above are in black but print yours...

This is a USB Nosecone mount for a friends E-Flite T-28 Trojan 1.1m RC Airplane. It will fit any USB Camera, shown in image is the USB Camera that comes with the Estes Astrocam Rocket. As far as i know it is not sold individually but as long as it...

This is my 3rd version of landing gear for the E-flite Opterra. Version 1 and 2 used double sided tape to attach to the unmodified keel of the plane. On a semi-hard landing I managed to break the plastic keel instead of having the tape come loose....

I re-sampled the original cowl so it would match and fit the original on the E-Flite 1.5m Texan. I added a support ring so the radial engine will fit nicely and allow you to glue it in place. In comparison to the original it adds very little extra...

Meticulously refine the specifics of the layout To be more precise, your task is to enhance and polish every aspect of the design in question. This may involve tweaking colors, adjusting proportions, or fine-tuning typography, among other things.

propellermotorframe

A four motor flying device that can be used for surveillance purposes. ...This is my second upload..

Belonging to the multi-rotor group, this aerial apparatus is equipped with four rotors.

propellermotorframe