e flite sukhoi su 29mm 3d models

This is a specialized trunion specifically crafted for use with an E-Flite 10 to 15 size nose gear retract. Designed for seamless integration with a press-in expansion nut (available at http://www.mcmaster.com/#94510a040/=10g8hmq), it provides a snug...

Here is a simple wall mount setup for the E-Flite F-16 Falcon (EFL9875). The holder is designed specifically for a 50 mm tire. The label easily fits into the top of the holder and can be left in place if desired. The sides are taller than the...

I based the design on the following hardware: FPV Camera: Lumenier CS-600 Super FPV Camera Pan Servo: HS-65 (The design also accepts standard SG-90 servo) FPV Transmitter: 600mW 5.8GHz A/V Tx Transmitter Battery: E-flite 2S 7.4V 20C LiPo I recommend...

This is a battery holder for an E-flite 11.1V 2200mAh 3S 30C LiPo Battery (Model #EFLB22003S30). I designed it for securing the battery inside my DIY RC airplane. An access hole can be cut in the fuselage (top or bottom) and the bracket can be glued...

I designed this custom support specifically for my E-flite Opterra FPV wing. When I'm preparing to land, I appreciate being able to glance at the side of the plane. The front of the support features a hole for cable management. All you need to do is...

This is a camera mount for the E-Flite 1.2m P-51D "June Night". Simply slide them on where the drop tanks attach. They are designed for the Replay XD 1080, which are a bit long in the tooth now, but I happen to have a few. They're also a bit heavy...

The modeled part is designed for an E-Flight 10-15 Electric retract in an E-Flite 15e Bonanza. This specific landing gear strut has proven challenging due to the aircraft's weight (5-6lbs) and high wing loading, which puts significant stress on the...

This is a USB Nosecone mount for a friends E-Flite T-28 Trojan 1.1m RC Airplane. It will fit any USB Camera, shown in image is the USB Camera that comes with the Estes Astrocam Rocket. As far as i know it is not sold individually but as long as it...

... This is a shroud/nacelle for the E-flite 28mm EDF unit, designed to bring more excitement to your discus launch glider. The tiny 28mm screaming ducted fan seemed like the ideal choice to achieve this! Check out the link below for the matched item.

This thing covers the inner vertical stabilizer fin slots for the E-flite Opterra 2M when flying with only the outer stabilizers. They are secured by the carbon spar as the original fins. My prototypes on the pics above are in black but print yours...

STEP files for the E-flite EFLG330 Tricycle 25-46 landing gear set. This covers the regular 90-degree main gear set as well. These are dimensionally accurate on the exterior dimensions, mounting holes, wire locations, pivot points, etc. The interior...

This is the complete set of missiles/launcher/stores-pylon for the E-Flite 80mm F-18D The LAU-115 attaches firmly to the wing pylons via powerful magnets that can be sourced separately, and are keyed into position so they remain perfectly straight. I...

STEP files for the E-flite EFLG330 Tricycle 25-46 landing gear set. This covers the regular 90-degree main gear set as well. These are dimensionally accurate on the exterior dimensions, mounting holes, wire locations, pivot points, etc. The interior...

I re-sampled the original cowl so it would match and fit the original on the E-Flite 1.5m Texan. I added a support ring so the radial engine will fit nicely and allow you to glue it in place. In comparison to the original it adds very little extra...

This is my 3rd version of landing gear for the E-flite Opterra. Version 1 and 2 used double sided tape to attach to the unmodified keel of the plane. On a semi-hard landing I managed to break the plastic keel instead of having the tape come loose....

This is my 3rd version of landing gear for the E-flite Opterra. Version 1 and 2 used double sided tape to attach to the unmodified keel of the plane. On a semi-hard landing I managed to break the plastic keel instead of having the tape come...

Air intake scoop for the AT-6 Texan 1.5m by E-FliteIf you want to support my contributions here, please consider leaving a tip https://www.paypal.com/paypalme/ShowmethedenaroNov 26, 2023Created G19 1500mm with several updates. Its a bit taller and it...

FIGHTER PLANE FOR 3D PRINTING The file includes a 3d model The files are made to be printed in resin and filament. ... Dimensions Y 43.68 - X 122.6 - Z 180 mm

Direct replacement that uses the original magnet assembly. The profile is slightly more radiused which I think is more pleasing in appearance. The original had nearly straight sides, top, and bottom. PDF detail drawing included. ... STEP and Inventor...

Have you lost or damaged your Eflite Timber battery hatch? Are you frustrated that it's not always available? Does the $15 replacement cost make you want to choke? Then try this 3D printed hatch. You decide on the strength vs weight tradeoff. I used...

A friend of mine who owns an Apprentice required a sturdier motor mount to replace the weak stock component. This part offers an identical fit to the original equipment manufacturer (OEM) item in terms of hole patterns and spacing, motor standoff...

I'm working on a project to fit two 5500 mAh LiPos under my Opterra. The goal is to significantly boost its duration and range. To achieve this, I've designed a system that involves cutting two small holes in the underside of the Opterra. This...

Made up some hangers for the Draco wings for storage. ...These have a small dust shelf for the connectors.

Timber frames are often used to construct the rear landing gear of aircraft.

I designed this similar to how my tiny whoop batteries are attached. It's printed in TPU and the middle rectangle wraps around the existing battery tray. I cut off the tabs since they are in the way. You won't need to disassemble anything. I...

Retract base

They corrected several flaws in the layout to ensure a smooth printing experience.

Rc Micro helicopter. ... Soft: Cinema4D

Just my design of a Insta360 Go camera mount for the Diatone TinaWhoop. ...Super Simple.

studio di modellazione e stampa 3D su Ferrari 412P 1967. please if anyone makes 3D prints or renderings with this project, please send me photos