e flite turbo timber 3d models

Descriptionthis is the brand new R5 TURBO 3E E-Tech from Renault made details like the little GoPros, and the different treatment between the front and rear wheels to name few included both collapesed and editable blend file with all modifiers, the...

So I did not read the manual and just flew the UMX. Well the landing gear pops out and breaks the .75mm thick plastic. I fused with soldering iron. Then glued the other side while I measured, drew and printed these tabs. ...Time will tell if the hold up...

Spinner replacement for the e-flite/FMS 1.2m P-39 Airacobra. ...It includes 2 blade spinner for high speed 6s version

Update: tray_2 For E-flite P-51D Mustang 1.2m, might fit other e-flite warbirds as well. Fits larger battery, should be able to fit 35mm x 45mm ish 0. Clip the original retaining clips on the rail. 1. Remove the wooden plate 2. Put battery...

A customized Fatshark TVL700(600) FPV camera snap-in holder for the E-Flite Opterra. With this design, the camera can be easily removed whenever needed. ... Print Settings Printer: Dremel 3D20 Rafts: Not required Supports: None Resolution: 0.1mm Infill:...

A work in progress, this is the front and rear console and side panels for the e flite SU 30. Also included is canopy frame for front and read as well as 3 mirrors for each. Mirrors can be covered with tinfoil to get a "mirrored" look. Will add...

You can download these original cylinders of the E-Flite AT-6 Dummy Engine for free to test-print. The detailed models are designed to push the limits of a standard 0.4mm nozzle 3D printer. To print them successfully, place the cylinder flat on its...

A realistic and precise 3D-printed dummy radial engine to substitute the standard front panel of your E-Flite AT-6 Texan's cowl. The building manual is part of this comprehensive package. This is a basic assembly kit which includes the base plate,...

I designed a micro drone propeller by utilizing the S4094 E-flite UMX ASK-21 airfoil, which underwent rigorous testing on the Drone Propeller Thrust Tester. The part was printed at a slow speed with a 0.2mm nozzle at 0.04 layer height and then...

I designed this micro drone propeller with the **S4095 E-flite UMX ASK-21** airfoil. Testing was performed on the **[Drone Propeller Thrust Testing Jig](http://www.thingiverse.com/thing:2302071)** (test results below). I printed this part with a...

I built the propeller using the **S4096 E-flite UMX ASK-21** airfoil. It was tested on the **[Drone Propeller Thrust Testing Jig](http://www.thingiverse.com/thing:2302071)** and results are below. The print job took some time, but it came out fine...

My original nose is a bit squished and was heavy anyway. This one is significantly lighter because the wall is just .4mm thick, can be slightly dented to the side, but also goes straight back to its original state. PLA is supposed to soften in the...

Holds a 6s battery in the right spot for CG in my Habu. Slides into position (my printer tolerances are great, make sure yours are) snugly, and the battery slides right into it. Velcro straps over top. Managed to crash my Habu, loose elevator...

Designed these landing gear after I broke a main strut and they were out of stock. These use rubber bands for suspension. You will need a 4mm X 25mm screw and a 3mm X 30mm. Both part will need to be printed with supports. ...The height is a bit lower...

For my SAE Aero 100 project, although not all parts are aesthetically pleasing, I am satisfied with the final outcome.

This object was made in Tinkercad. ...Edit it online https://www.tinkercad.com/things/gvb1uMzVjg3

Su30 retract base replacement

This is a highly advanced, operational elevator tail gear system.

Designed for a missing missile tip on 64mm Twin A10!

Flying to your favorite spot is always an exhilarating experience, but what happens when you arrive only to remember you've left your trusty screwdriver behind? Forgetting your tool can leave you grounded, unable to take to the skies in your...

PETG 0,3, infill 30%

This is a replica of the replacement for the nasty foam underbelly AIM7 missiles on the EFlite F-4 Phantom. The "top" fins are omitted because they would be embedded in the underside of the model. Four parts fit together via pegs. Only 5% infill is...

Simple wall mount for UMX A-10

This is a camera mount designed to be used with the RunCam2 camera pod. https://www.thingiverse.com/thing:4700731 You will need to use longer screws (m4 x 25mm long). ...I printed this at a 45 degree angle with supports on the base (see pics).

The Opterra is notorious for its reluctance to land, preferring instead to hover endlessly. ...To rectify this issue, I recommend installing airbrakes, measuring 250mm in length and available under J Perkins part number JP4406305.\r\n\r\nThis custom...

not the prettiest, but it will fill the void

I designed this after I lost the skid on my maiden and didn't realize it until I was home.

<p>This a replacement part for a RC airplane model that broke after a minor crash. &nbsp;The part is available form the maker, but it is sold as a larger kit and is expensive. &nbsp;The part was not difficult to design and costs little to...

Hang your avanti on the wall. ...It rests on the tailcone, and there is a brace for the top that prevents it from tipping.