e mount to canon 3d models
2199827 3d models found related to e mount to canon.thingiverse
Sony NEX/E mount to Canon EF mount adapter. This allows use of Canon EF/EF-S lenses on a Sony NEX body (or other Sony E-mount body). The flange to flange distance of this adapter is technically 25.4mm, but as printed on my Makerbot Replicator 2 it is...
thingiverse
Adapter to connect Canon FD lenses to Sony E mount bodies. Flange distance difference from Canon FD to Sony E is 24mm, but the adapter is 23.5mm to allow for printing tolerance and to ensure focus to infinity. Adjust this in your slicer if your...
thingiverse
This is an adapter to mount old/vintage Canon FD lenses to modern Full-frame or APS-C Sony E-mount Cameras. The adapter has an internal "pin" that triggers the automatic aperture lever, thus allowing you to select the aperture that you want. This...
cults3d
I share with you my design to adapt Canon EOS mount EF lenses (5D 6D 1200D 700D 750D 800D 70D 77D 80D...) to mirrorless Sony E-mount cameras (A7 A7II A7III A7RIV A5000 A6000 A6300 NEX-3...) The design has been perfectly adapted with a Sony A7II...
thingiverse
Remove gopro lens, Get a cheep lens and take apart to get the IR-Cut filter or get one to fint you canon lens. Use a spring from ballpoint pen cut in half for lock spring. Gif Lens Instruction For IR-Cut The IR-Cut has nothing to do with the focus...
thingiverse
This fits on the outside to prevent vignetting. Instructions WARNING Not been tested! ... Because it goes outside of the focuser, it takes away 30mm of potential back focus (which I dont have) so I...
thingiverse
I remixed the original M42 adapter to fit better on the Helios 44M-2 and the 44M-5 I had, fixed the lens orientation and made the radius bigger so the two holes can fit better.
thingiverse
This is an adapter to use any Nikon lens with the F-mount on any Canon with an EF/EF-S mount. It has worked and fits snugly on the lens. There is a little notch on the side of the adapter that allows it to lock onto the camera body. Give heavier...
thingiverse
... ...Since i worked with Canon, the angle finder C was the item to have. I recently switched to Sony but sadly Sony does not make an angle finder that fits My a7iii or a7Riv. I made an eye cup mount for the canon angle finder. ...Hope you find it useful.
thingiverse
A mount adapter from Canon RF mirrorless cameras to Konica Hexanon AR. The flange distance is set to allow for infinity focus. I tested the adapter on my R6 with a Konica 40mm 1.8 and it works great! ...
thingiverse
Adapter to attach a Canon EF-mount lens onto a 2" barrel. ... Remember that PLA can transmit a small amount of light, so consider painting the inside of the adapter!
thingiverse
This Adapter is for bigger objektives. ...From Minolta to EF Mount. There is a big ring that fits on the Canon, so the force on the bayonetadapter gets minimized. You can Print it without any Support. ... Have Fun ;-)
thingiverse
So I adapt the EOS-female side from "Canon EF Extension Tube v1 - 50mm by martinmunk" and create T-Mount by using "T42 to Canon EF-S lens Adapter (Work in progress) by Bootdsc" as a mold. I print it with Prusa i3 Height 0.2mm Nozzle 0.4mm No support...
thingiverse
This allows a Canon EF mount camera to fit OVER a 28mm outer diameter microscope eyepiece. I have tested this with my Swift SW350T, but I think it would work for any 'scope where the eyepiece is 28mm OD. There are provisions for 3x M4 nuts and 3x M4...
thingiverse
The original Canon EOS-Nikon F mount Adapter by nameless911 was the basis for this remix. I added 0.44mm to the base flange to increase the Flange-to-Focal plane distance to more accurately focus at infinity with the Nikon 55mm Micro-Nikkor AI lens...
thingiverse
This is a simple Canon EF Mount to M65 threaded adapter. This is to connect a Canon DSLR camera to a Tele Vue Paracorr. The paracorr uses an M65 thread connection and this has an extra 12mm spacing added to bring the camera to the 56mm focal point of...
thingiverse
-Update: Mount MKII has a bigger external diameter in order to compensate for the ABS shrink issue. It didn't work as I expected but I uploaded it in case someone can learn from my mistakes. After a little work with the rotary tool for sanding and...
thingiverse
Canon EOS 1100D with 28mm 1:2.8 lens Watch out your lens will become macro ones this due to the big distance from the sensor. All uncompressed photo are on the zip file. The adapter and camera photos aren't taken with the adapter. ... UPDATE...
thingiverse
Attach the new ball to the white mount that gets held between the cartridges shell halfs. Assemble the cartridge again. The part for version 1 is still downloadable, but I have had reports of the part not printing correctly, so I'd strongly...
thingiverse
To mount EOS lens on Nikon Z. ... Total backfocus 44 mm (16+28).
thingiverse
... version of the model. ...Sometimes it's just loose on the camera mount, but it's still usable and focuses perfectly. Achieve the distance between the optical center and the camera sensor. ...I will post the final version ready to print on my profile
prusaprinters
Thanks to the linked makers I was able to merge them and to create this EF to M42 lens adapter. It works well for me but it is possible to improve it. If you printed the design you have to drill a hole at the spot where a camera lens holder Pin is,...
thingiverse
Thanks to the linked makers I was able to merge them and to create this EF to M42 lens adapter. It works well for me but it is possible to improve it. If you printed the design you have to drill a hole at the spot where a camera lens holder Pin is,...
thingiverse
E-mount to DIN 23mm microscope adapter Use black filament otherwise the image may be degraded.
thingiverse
The Lacerta M48 to Canon EOS Off-Axis Guider (OAG) has a fairly stout pick-off tube, but there still can be some rotation or slippage of the T-mount connected to the guide camera, particularly if the guide camera cable snags. This 3D-printed part...
thingiverse
(may hurt FF canon cameras due to mirror hitting, i don't have a FF camera to try,so be carefull) It works perfect on a Croped Sensor DSLR like Eos 60D,700D,etc. ...UPDATE: Better fitting and better focusing to infinite Print Settings Printer Brand:...
thingiverse
If you want to know more about what these cameras are capable of if mounted to a better lens or telescope with tracking, check out (not mine) this video youtube.com/watch?v=JHiCNmYdkaE (not mine!) or goto a forum such...
thingiverse
This mount allows you to retrofit Canon bayonet mount 8mm lenses (produced in 1957) to common D-mount adapters that will fit popular digital SLR cameras. The lenses work best with Pentax Q digital cameras. Please feel free to update this print with...
thingiverse
The Adapter to fit Tokina 135mm Lens with Om Olympus mount to my Sony A7 with E mount