e3 sentry 3d models

This is a remix I did from Waggsters all in one and Hunterius_primes tft enclosure. I wanted my CR10's to have a reduced footprint when I upgraded them and I made this. Works great and easy to put together. ...Im sorry I don't have screw list.

A redesign of my previous anemic filament guide arm. prints in a single piece in about 2.5 hours. I made this with .4 layer height and it worked, just required a little prodding to loosen the wheel but its a great fit. although i suggest .2 layer...

Adapted from https://www.thingiverse.com/thing:4622318 Modifications: - Resized to add BTT UPS - Adding interlocking nuts

It is a leased E-3 aircraft, but features Boeing 767 airframes, KC-767 (tanker equipment) and E-3 (airborne warning system equipment). These are displayed in ascending order of type, including aircraft, engine, avionics, communication systems, cabin...

This is an adaptation of the Anycubic Mega Zero SKR Mini V2.0 Enclosure, to be printable as two flanged pieces to give better top surface quality. The USB hole has also been enlarged slightly to allow the use of stock Creality v4 boards with the same...

I found that Juanolo's remix's BLTouch mount was a bit low (my clone is a smidge longer than the real one) and when retracted the tip was barely above the nozzle height, at high risk of snagging on any stray filament or spaghetti. So I raised the...

This is an adaptation of the [Anycubic Mega Zero SKR Mini V2.0 Enclosure](https://www.thingiverse.com/thing:4584262), to be printable as two flanged pieces to give better top surface quality. The USB hole has also been enlarged slightly to allow...

Took Efflon's amazing case [ https://www.thingiverse.com/thing:4749766 ] and made the screen mount holes 4.65mm to allow for 3mm thread inserts

This is my remix to mount heatbed cable chain to electronic case. I simply took thesamurai (https://www.thingiverse.com/thing:4754607) design and I added cable chain mount, made bigger vent holes and bigger opening for USB cable (origianal one doesnt...

Motherboard plate / adapter for tevo little monster or anet a8, tolerances are tight enough to thread if you would like to add on a cover for the anet, left room on the bottom for additional cooling and access to mosfet cooling pads. Secure using...

Remix features: -Added SD card adapter slot -Added cover for screw holes (This is optional) -Small cutout for z-stop wire to go through the case cover ***Note the micro-USB on SKR board will not be accessible as I don't intent to use...

I am starting to enclose my ender machines and didn't find what I wanted online so made it myself. This is a simple case that will hold the LCD screen and let you attach it to a wall or cabinet. This is the first of my designs that I will be...

So, I've resurfaced the screws as recommended by numerous commenters. Additionally, I've recessed the surrounding area around the USB and SD slot. ...This modification now accommodates larger USB drives, as clearly illustrated in the accompanying image.

This is a great case, but I needed a place for my SD Card, so I added one. ...I also moved the fan closer to the SD card slot to give more room next to the USB port.

Originally intended for Ramps 1.4 a LCD controller 12864 https://www.thingiverse.com/thing:1694188

A redesign of my previous anemic filament guide arm. prints in a single piece in about 2.5 hours. I made this with .4 layer height and it worked, just required a little prodding to loosen the wheel but its a great fit. although i suggest .2 layer...

Youtube timelapse : https://www.youtube.com/watch?v=GcEWqd5_UVw GXS remix of Main board box lid finish ,Remove and fit - realtime https://youtu.be/rmLJLdj6Bis i also had to add Voltage Step-down from 24v to 12v found here...

Do you want to use your filament sensor? Do you want to have hydra upgrade but still want to feed your extruder from side? Solution is here. <h4>Tips</h4> - I did remove the connector's insert from original extruder. Just you need a heat gun.

<p>PETG or higher is better&nbsp;</p>

<p>Adapted from <a href="https://www.thingiverse.com/thing:4622318">https://www.thingiverse.com/thing:4622318</a></p> <p>Modifications:</p> <ul> <li>Resized to add BTT UPS</li> <li>Adding interlocking nuts</li> </ul> <h3>Print Settings</h3>...

航空自衛隊のE-3ですが、767本体とKC-767(空中給油機)とE-3(早期警戒機)を部品表示切替式にしてます、序に フラップ、エルロン、エレベーター、ランディングギア、エアブレーキ、ラダーも動作切替式です。 注意：本品は簡易モデルです。 It is not a stl file for 3D printing.

Remixed the Big Tree Tech TFT 35 mount from tom66 by mirroring the right hand bracket to left hand. This will now work to mount the a TFT 35 on an AM8. ... 8/2 Revised Bolt Hole Pattern for back plate 8/5 Added extra space on side to allow faceplate...

<p>This is my remix to mount heatbed cable chain to electronic case. I simply took thesamurai (<a href="https://www.thingiverse.com/thing:4754607">https://www.thingiverse.com/thing:4754607</a>) design and I added cable chain mount, made bigger vent...

<p>I have to give the model 10mm offset from Y axis extrusion to clear the enclosure from Y end-stop&amp;y motor.&nbsp;</p><p>The controller board will be installed upside-down and having the hot end&amp;heated bed connectors facing Z motor...

Split Helmet_Bottom using meshmixer as I could not find an orientation that would slice for my E3v2. ...Prints well with skirt only.

Control box for the SKR pro 1.2 board and the tft35 touch screen set. Front/Rear cover plates are optional, the grille is used in front of the fans. Supports needed on long openings, print the top with the rear of the top on the build plate.

This is my remix to mount heatbed cable chain to electronic case. I simply took thesamurai (https://www.thingiverse.com/thing:4754607) design and I added cable chain mount, made bigger vent holes and bigger opening for USB cable (origianal one doesnt...

I created a bed handle with a camera mount for my Ender 3 printer by merging two separate designs together. I liked the low-poly handle made by saamirt and the swivel camera mount from jmillerfo, so I combined them in tinkercad to create a single...

I saw the electronics case and thought that would work good with an SKR board. ...I will upload more pictures when I print and Install it

trek domane gen 4 al, end cap for othe hidden cable routing