e3d extruder
79015 3d models found related to e3d extruder.cults3d
I've modified extruder on my DaVinci Pro so it can work with E3D V6 Hot Ends. Works way better than stock one. ... https://youtu.be/6L33GBkl6Wc
thingiverse
I've modified extruder on my DaVinci Pro so it can work with E3D V6 Hot Ends. Works way better than stock one. ... https://youtu.be/6L33GBkl6Wc
grabcad
This is a model of the E3D hot end from E3D-Online.com This was modeled using exact dimensions from the documentation here: http://e3d-online.com/Documentation for V4 E3D. This is modeled as the 1.75mm bowden heatsink. ...If there is demand, direct...
pinshape
Summary Fan duct for E3D extruder with both radiator and filament cooling with 40mm fan. Reference Radiator outer diameter .98 in. ...Overall size 1.92H x 1.58W x 1.28D.
thingiverse
Fan duct for E3D extruder with both radiator and filament cooling with 40mm fan. Reference Radiator outer diameter .98 in. ...Overall size 1.92H x 1.58W x 1.28D.
grabcad
... least. This mount enables to mount E3D extruder Lite / V6, Linear block under the mount, a cooling fan, & a proximity sensor. It is very compatible for 3D printers. ...I'd appreciate for any advises in development or improvements in the design.
thingiverse
This is an extruder motor mount that I designed to use with an e3d extruder. It mounts on top of the frame in place of the spacer for the led board. I also included a picture of my filament holder mod that I did as well. I drilled a 5/16" hole in the...
grabcad
It is concept model in which i've used E3d extruder as an replacement of traditional extruder on Creatbot DE 3d printer.
thingiverse
you need m3 screws, an e3d v6 extruder, one fillament feeder with tube and one 30 mm fan.
pinshape
This is a support that doesn't need anything out of your E3D extruder. It fits on the cold end of the extruder. The fan must be 40x40. ...Indicated print settings: ABS 1.75, print speed 50 mm/s, print temperature (depending on you filament supplier)...
cults3d
Carriage to mount an E3D extruder and a BLtouch level controller on an Anet A6 printer...
thingiverse
This is an entire low profile X-Carriage setup for a E3D V5 extruder. This X-Carriage setup will allow the hot end to mount with enough clearance for the bearings and still have the capabilities for auto bed leveling. 6/22/14 An E3D V6 version has...
thingiverse
I initially began designing this extruder to work with the E3D Hotend because of the sloppy fit on the original version but the one thing I really wanted, was to install 60mm cooling fans. In addition I design a E3D 40mm shroud that works with v4,...
thingiverse
I designed this to hold the wires going down to the extruder as well as the fan wiring. ...It mounts in place of the spacer for the led board and could be used other places as well.
thingiverse
E3D Extruder - Chinese Clone - Fan Mount 40mm Print Settings Printer Brand: RepRap Printer: Prusa i3 Rework Rafts: Yes Supports: Yes Resolution: 0.2 Infill: 50
thingiverse
This duct mount replaces the one provided by Charlie's 3DT, allows space for the e3d extruder fan. ...(Original name was "Charlies3DT_-_Prusa_i3_Fan_Holder".)
thingiverse
It is a simple object to adapt a E3D v6 extruder to the Wasp 20x40. It need to be printed twice... ... Instructions print twice and mount it
thingiverse
(designed for eBay i3) It incorporates my E3D extruder design, found here:http://www.thingiverse.com/thing:991803 It can be changed between Bowden and Direct configurations by the removal of two M3 bolts. ...It uses a 50mm blower fan for parts cooling,...
thingiverse
This is a carriage for two bowden e3d extruders, two fans on the fins, and two fans on the nozzles all adapted to the rails of the Printrbot Plus v2. ...40mm fans, M3 screws 6-32 screws (x7), nut (x1) LM8UU linear bearings four sections, each can...
thingiverse
Use of genuine E3D hotend is recommended for increased performance Required Parts -Flexion E3D Extruder -NEMA17 Stepper Motor currently using a 48mm Version ( Factory Black Widow Extruder Motor can not be used do to shaft being turned down to accept...
thingiverse
Replacement carriage for the Anet A8 plus for a E3D Titan extruder and V6 hotend and inductive probe. ...You should print the carriage on it's side with support for the motor support , you can manually add this with custom supports , the rest will print...
thingiverse
I liked the simple design of the OB1.4 Dual E3D extruder from downeym, so I remixed it to fit on the RepRapPro Mendel carriage. It replaces the complete front nozzel mount of the carriage, so its easy to swap it with the original. I placed also two...
thingiverse
BLTouch mount for the E3D Titan extruder. This design can be used as the basis for a mount to suite your printer X carriage type. It is an addition to my cooling fan mount http://www.thingiverse.com/thing:1537971 There are two versions,...
thingiverse
Soporte para ventilador de 40mm x 40mm para Extruder E3D hottend prusa i3. ... Nota: En la imagen el ventilador es de 50mm
thingiverse
... end. ... So the plate that the extruder mounts to extends below the tip of the hot end. This model lowers the platform so that the extruder sits at a level appropriate for the E3D, but still allows mounting to the Printrbot Plus X-Carriage assembly.
youmagine
The holder is created to fit at K8200 T-slot and to provide a well-fixed positioning for Chimera/Cyclops extruder, developed by E3D (http://wiki.e3d-online.com/wiki/Cyclops_%26_Chimera_Documentation), as well as to align the inductive sensor we use...