e3d v6 direct drive anet a8

This is a specially designed E3D or Lite support for the Anet A8, carefully crafted to ensure optimal print quality and performance.\r\n\r\nFor effortless cable management, consider integrating an Adapter to Cable Chain // Filaflex tensioner from...

I'm using a direct drive setup on my A8 with stock extruder motor and parts cooling fan. The build is designed for fan nozzles intended for the stock extruder. I added a small post to attach one of the wire clips from the A8 kit for strain relief. So...

Just my design of a E3D v6 Direct Drive upgrade for my Anet A8. No firmware flashing required, just a straight replacement of original extruder system. Enjoy ! ...All parts have been printed on my new Artillery Sidewinder X1 in 0.2mm layer height with...

Just my design of a E3D v6 Direct Drive upgrade for my Anet A8. No firmware flashing required, just a straight replacement of original extruder system. Enjoy ! ... All parts have been printed on my new Artillery Sidewinder X1 in 0.2mm layer height with...

Anet A8 E3D V6 Direct Drive. This printer is a 3D powerhouse that's taking the world by storm. With its robust build and direct drive extruder, it's capable of producing high-quality prints with ease. You can also find similar instructions below on...

I'm currently assembling another Anet A8 E3D V6 direct mount carriage. ...Once finished, I'll be putting it through a series of tests to see how well it performs.

A direct drive carriage designed specifically for Anet A8 (or other 8mm rod 45mm space i3 style machines) mounts an E3D v6 or clone hotend and a block-style inductive sensor. Why did we choose this design? The Fanduct is actually a minor...

This is an updated version of my Anet A8 E3D V6 Direct Drive remix (https://www.thingiverse.com/thing:3913249). The extruder motor mount can now be removed with two M4 screws, providing a sleeker appearance when in Bowden mode. For easy removal,...

I worked again on the frame X original to make it lighter, adapted a belt holder, created one part to fix Bltouch and finally drawn a last part to put a 40mm fan for hotend (the original is too noisy). Drawings are not perfect I had to make some...

I designed a cable chain solution for my E3D v6 lite hotend upgrade, using the Thingiverse model http://www.thingiverse.com/thing:1757300 as a starting point. Since no suitable option existed, I created new parts in TinkerCAD and here is the result.

This Remix add BLTouch support.Support for almost any X belt tensioner designed for Anet A8.Print in PETG or temperature resistant filament.

It also accommodates almost any X belt tensioner designed specifically for Anet A8 printers. ... For an optimal fan mounting solution, consider trying this design: https://www.thingiverse.com/thing:1571526 Alternatively, explore one of these remixes:...

I require a replacement part for one of my sensors, and fortunately, I have a spare SN-04 Stock Anet sensor stored in my toolbox. ...To ensure seamless integration, I've decided to modify this part to match the firmware settings of my existing setup.

This custom idler is designed specifically for the Anet A8 and should fit seamlessly with its factory idler mounts. Check out this compatible design on Thingiverse: https://www.thingiverse.com/thing:2773206. The stepper motor in this setup is...

E3D V6 direct drive by 3Displacement suitable for v-slot x axis

A SHORT PIECE OF PTFE 4mm TUBE: it goes between the motor and the e3d v6, you put it in the pneumatic clamp on the e3d v6 and insert all in the 4mm hole directly on top of it and then cut it next to the extruder wheel, to make it easier for flexible...

I have referenced the ones below to replace the extruder parts of my Anet A8 printer. https://www.thingiverse.com/thing:3913249 https://www.thingiverse.com/thing:3599905 https://www.thingiverse.com/thing:3603004 ...

https://www.thingiverse.com/thing:3913249 https://www.thingiverse.com/thing:3599905 https://www.thingiverse.com/thing:3603004 https://www.thingiverse.com/thing:2425783 However, I didn't like the set of Fan-shrouds provided, and even touched the...

... with supports attached directly from the build plate. For optimal performance, consider using an E3D V6 silicone sock unless opting to print the fan nozzle in ABS material. ... Proper printing orientation is essential to achieve the best results.

... melt holes in the fan duct. Your X and Y home offsets will change with this mount; it's now -16 for X and -8 for Y. Print Settings: Printer: Anet A8 Rafts: No Supports: Yes Resolution: .25 Infill: 35% Cubic Subdivision Notes: Used a 15mm brim.

i printed it at .3 initial layer .25 layer height 35% cubic subdivision infill support from bed only at 50 mm/s Should probably add dont print it out of PLA if you want it to last Can be printed all together on the build plate of anet a8 in one go...

The hollow threaded rod that mounted the MK8 hot end to the lower part of the filament tension bracket is what you'll use to secure the stepper motor to the E3D hot end. Simply spin the E3D hot end until the motor securely attaches to the mount. ...This...

I managed to find a way to align dual extruders in the y-direction, freeing up valuable space on the hotbed. One-piece designs often prove challenging without supports, and attempting to print with them results in a non-functional outcome. After...

It's not experimental anymore, it's functional and for now I don't see a need to improve it further because it works extremely well. This design was created to be used with this carrier that functions very smoothly, better than IGUS and LM8UU...

I've reworked this design to seamlessly integrate with the 3D Touch sensor, bringing it into alignment with modern technology. ...To make this happen, I've included both Fusion360 and STP file formats for your convenience.

UPDATE 11/14/2023 - I no longer own a RepRap Orig. Prusa i3 MK2, I printed the parts and upgraded it, I tested it and sold it, it was only built to be sold. Therefore I cannot really provide much info on it. Except that it worked well! I used screws...

Thisi is modification for [Anet A8/A8 Plus X Carriage for E3D V6, original direct drive extruder](https://www.thingiverse.com/thing:5215000) I made slots for nuts, improved heat dissipation from the hotend radiator, rounded the edges This is a...

Thisi is modification for Anet A8/A8 Plus X Carriage for E3D V6, original direct drive extruder I made slots for nuts, improved heat dissipation from the hotend radiator, rounded the edges This is a replacement for the standard Anet A8/A8 Plus X...

This is a replacement for the standard Anet A8/A8 Plus X carriage for use with an E3D V6 hotend with no additional changes. It uses the original part cooling fan, direct drive extruder, and belt tensioner. The backplate matches the original, so some...

I customized several designs to create a semi-direct E3D V6 configuration for my Anet A8. Using Tech2C MK7 compact bowden extruder, Tech2C E3D v6 bowden mount, and Allandwelds Anet 3 bearing x carriage, I created this setup to print a component for...