e3d v6 fan upgrade

Minimalistic fan duct for 5015 turbine and 404020 (or 404010) fan, remixed from https://www.thingiverse.com/thing:4615905 and https://www.thingiverse.com/thing:2886505 I created this for my custon direct drive.

air guide / fan duct for 30mm fan - http://www.thingiverse.com/thing:701002 * Fan Shroud - http://www.thingiverse.com/thing:351280 * Fan Bracket - http://www.thingiverse.com/thing:1249991 Preview of printing:...

... with a parallel arm distance of 43mm. The 5015 fan is excessively powerful, so it's essential to set the fan speed to 80% to avoid thermal errors. To install this effector, you will need: * A 5015 fan * A 40mm fan * M3 bolts and nuts * ABS filament

It's replacement of the stock layer fan duct which has long duct. ... The Blender version is 3.1.2.

Remix to position the Printrbot Simple Metal's heat block under a 40mm Noctua fan, ensuring maximum airflow. Although there are doubts about the fan's strength, it will be worth testing its capabilities. ... Fan used:...

I took inspiration from the original design by mnielsenau, but because I wanted more focused cooling directely at the nozzle the 40mm fans were replaced by radial fans. !! You will need relativeley long M3 screws to mount the fans !! !! The hole...

About Assembly To assemble the new fan holder, you will need to print the main fan holder (Fan_duct_filament_V2.STL) and two nozzles (Fan_duct_filament_V2_nozzle_x2.STL). All screws (4), nuts (4), and washers (6) have M3 size. You'll also need two...

Tevo Black Widow Fan Duct and Bl Touch Mount Added a Volcano version as well I designed this to replace the stock fan that was floating in mid-air causing uncontrolled air to cool the extruder The integrated BL Touch mount helps clean up the look and...

Compact blower fan holder for h-bot. Designed for Bondtech direct extruder. ... You can buy blowers here https://goo.gl/VLpumn Slicing tested in Simplify3D.

... 2/3 of the air to the heat sink, and 1/3 to the filament. Anyway, the air flow for filament is way bigger than I expected, so I shared my design, hoping to help you. This fan duct can cool both extruder and filament with only one 40mm fan.

The fan is adjusted at a precise angle of 15 degrees, allowing for an enhanced line of sight directly towards the nozzle.

I added two clamping "wings" to secure it firmly onto the E3D cooler using a zip tie, since the original design tends to be loose and sometimes falls off after extended print sessions. This modification was necessary to prevent such incidents from...

To assemble this fan duct, you'll need to gather several components: two M3 locking nuts, two M3 30mm bolts, two M3 8mm bolts, one M3 20mm bolt, twelve M3 12mm bolts, and one 30mm 24v fan. Additionally, you'll require two 40mm 24v fans. Update:...

I have modified the original holder to fit the Fan Duct. ...I have mounted the left screw to countered it on the other side with a nut.</p>

It's made specifically for 40mm fans and I discovered this design works slightly better than my other one which blows downwards on the object. Instead, this design blows air across the object after passing through the nozzle tip. Print Settings: ...

BOM and Other Used Parts: I used the following parts for this project: * 4 M3 nuts * 6 M3 x 16mm screws * 2 M3 x 25mm screws Customized Components: To enhance airflow, I designed a 45-degree air guide/fan duct for a 30mm fan, which can be found at...

Compact Fan Holder for H-Bot Extrusion System. Designed Specifically for the Bondtech Direct Drive Extruder. ...Purchase High-Performance Blowers Here: https://tinyurl.com/VLpumn Rigorously Tested with Simplify3D Slicer Software.

This project is still under development as I attempt to integrate a radial cooling fan into the carrier object. ...It remains unclear whether this modification will function as intended, and results may vary significantly from one attempt to another.

I just imported one of original Main_Body parts with a 40mm fan and a sensor, and cut off the sensor part, otherwise identical to the original design. Only the "Main_Body" part is included in this upload. ...Get the rest of the required parts from...

... I only glued together the base piece with the same piece mirrored and I mirrored the Fan Duct. Thats all I did. ...Please give credits (and love and tips) to the creator of the original part => mediaman https://www.thingiverse.com/thing:3393889

... it was easy to chop off the extra and make one that works. I left the model on it's side as the original designer had it, but I recommend printing 90 degrees rotated so the fan mount is on the bed. No support required after rotation. ...

If you have either a Mosquito or a Dragon hotend, this is the fan duct you want, it has been optimized to use nearly 90% of the 4020 fan CFM's versus the stock fan utilizing only 68% There are many pictures to help guide you through installing this...

Make sure the heatblock has the heater cartridge towards the rear of the printer, or you'll melt holes in the fan duct. Your X and Y home offsets will change with this mount; it's now -16 for X and -8 for Y. ... Print Settings: Printer: Anet A8 ...

Designed for use with 5015 radial fans and 4010 fans. You may be able to use it with the brackets for CR10 and xcr3d 2in1-s1 provided here, but it is not tested: https://www.thingiverse.com/thing:4204708. A Fusion360 file with all the models is...

Standard clearance has been approved for the standard fan shroud, enabling it to perfectly align with the hot end while maintaining proper distance from the carriage to prevent fouling. ...A YouTube video showcasing the carriage's functionality can be...

Then while waiting for the 5015 fan one of my prints printed split and when I opened it I noticed it had major issues in the air tunnel &nbsp;(see pic). &nbsp;So I am making a version that I will glue together. &nbsp;I may try to use a snake cam to...

Created with TinkerCAD's innovative design capabilities, this custom mount empowers users to securely attach a 40mm radial fan directly to its front-facing surface. ...By seamlessly integrating with the original carriage, the mount provides a stable and...

I've been battling overheating problems with my printer enclosure, so I took a step further and added more cooling fans to the mix. Built to be compatible with the Quick Fit Carriage System by BETLOG, this design is ready for action. ... Printed in...

[UPDATED] I've upgraded the design to make it more visually appealing. I've added a chamfer to some edges and a fillet to others. Everything has been rounded out to give it a professional look. The original low-poly version is still available in the...

https://www.thingiverse.com/thing:3913249 https://www.thingiverse.com/thing:3599905 https://www.thingiverse.com/thing:3603004 https://www.thingiverse.com/thing:2425783 However, I didn't like the set of Fan-shrouds provided, and even touched the...