e46 dashboard 3d models

V1 The hero section for the game Gloomhaven that inspired me had tiny slots for character boards made of cardboard. Maybe we'll play a newer version with features like this; I have no idea. So, I designed one myself and based it on the previous...

I ran out of time, but I believe the work completed meets the required standard.

For use with Star Wars Imperial Assault board game. The top track is for health, while the side track is for strain. Designed for use with a 10mm/1cm standard cube. Will accommodate a sleeved character card. ... Small 'tray' area on the right can...

This dash is engineered to seamlessly integrate into the Vaterra Ascender Blazer body. A specially designed slot beneath the dash provides a convenient installation point for a micro servo, which can be secured using a long screw that attaches...

customized models on request

Organizer for gear tokens for Rallyman GT. Designed for 6mm magnets. ...Full set is too tall for RM:GT box, but two sets fit well in RM:Dirt.

This object was made in Tinkercad. ...Edit it online https://www.tinkercad.com/things/1qmaT6kHF71

This is a prep for the Vaterra Ascender Bronco Body. Print: 2x Mount Bracket, 1x Wheel, 1x Dash I attached the L brackets to the body first, then secured them to the dash with Insta-Cure CA glue in 1-3 seconds. ...To achieve the best visual impact, be...

This object was made in Tinkercad. ...Edit it online https://www.tinkercad.com/things/1qmaT6kHF71

This object was made in Tinkercad. ...Edit it online https://www.tinkercad.com/things/1qmaT6kHF71

The cribbage pieces can be purchased on Amazon cheap. ... This removes the cardboard from the game but also allows your opponent to gauge health remaining as well without asking.

I finally found a suitable coin holder for my Toyota by designing one myself, taking inspiration from one of the car's covers. ...The new design perfectly matches the trim, allowing me to store a few extra coins compared to the original factory holder.

sheet metal

A simple box that contain a TM1638 module (8 bicolor led, 8 push buttons and 8 7segements display) + a 8x8 led matrix (based on mx7219) and a arduino micro. To be used with the sim hub software in a wide catalog of racing games have several DB9...

Solidworks 2013

Mounting the Touchpad of your Dobot Mooz 1 or 2 just got a whole lot easier with our support jig. ...By using this clever tool, you'll be able to secure the Touchpad in place on any flat surface, like a table.

Vw T4 cover for where the buttons go. Mine had a hole in it and so i re-printed it in a more cheerful color than black. ...

This object was made in Tinkercad. ...Edit it online https://www.tinkercad.com/things/kzsw8iayltI

sheet metal

Just Print and insert the hook to the blank.(i tried to print as one piece, but then the hook breaks as you apply force to it because of the bending force is equal to the layer direction) I had another model than that of Zipfl0815 in my T4...

It is not exact representation of the real one, but more than 90% achieved.

https://www.youtube.com/watch?v=j4qzbF8xf20 Part List: 3mm Polycarbonate Sheet Arduino Nano Pinless (wires soldered directly onto the nano) 2 Max7221 Displays 1 8x WS2812B Strip 2 M3 Screws Driven by homemade software at...

Test model

This model is used in the assembly of a personal project. The project is about the realization of a streetfighter (motorcycle) based on the classic gpz900r from the 80's. On request I can upload a Solidworks 2011 model. The model is build up so...

if you like the project please send a small donation to a local charity organization for the 5inch vocore https://youtu.be/KcMU6TCMYZ0 https://www.instagram.com/pwistudio/ https://www.facebook.com/pwistudio

Holding pins for Lancia Ypsilons dasboard.

Ender 3 0.28 layers 100% infill

Made a print in place twerking STL with jiggle tits, ass, and bends at the knees.

Inspired by item #283082. This design is intended for newer model VW T4 Transporters. ... The face of this blank measures 26.1 x 44.2 millimeters.