e46 phone mount 3d models
387163 3d models found related to e46 phone mount.thingiverse
This should fit for any E46/36/39 drive by cable pedals (only been tested on an E46) This piece is meant to be put in the area where the previous mount was. recessed into the carpeting and touching the floor pan. The recess in the bottom of the part...
cults3d
Correct me in the comments if I'm wrong) length 160.8 mm width 78.1 mm thickness 7.4 mm The mount was made for the phone along with the case! ... You will have to screw the mount model to the audio cassette, if you do not have an audio cassette, you can...
thingiverse
Correct me in the comments if I'm wrong) length 160.8 mm width 78.1 mm thickness 7.4 mm The mount was made for the phone along with the case! ... You will have to screw the mount model to the audio cassette, if you do not have an audio cassette, you can...
thingiverse
Created to raise my rear shock absorber top mount (3.5" higher) for a lowered e46 with shocks that bottom out.
thingiverse
UPDATE(18/01/2020): https://www.thingiverse.com/thing:4111301 Was having some trouble to fit the "e46_adapter" to my seat, and also to my fire extinguisher. ...This redesign is a little bit taller, and the gap is wider between the mounts
thingiverse
This is a very simple base plate with holes that line up with existing bolt holes inside the rear seat of an E46 M3 convertible (and, presumably, other E46 convertibles). My goal was simply to do a subwoofer install that a) used no trunk space, and...
thingiverse
I also made a file for a E46 Cabrio rear speakers which has a 130mm original speakers, since i could not find any low profile 130mm speaker i made a reduction on 10cm suits for Crunch DSX 4.2 Components. Fort test print i used PLA so i knew if...
thingiverse
This is to allow for indipent rear abs sensors on an R200 Nissan diff, spacing is designed for a OEM S14 ABS reductor ring and the sensors are from a BMW E46 My setup is using a Honda S2000 pump, but these sensors will work with the more popular MK60...
thingiverse
Now you can easily slide this mount in order to fit the seat support. ...No more struggle because the main support was split in 2
grabcad
Should fit E30-E90 models modification required for proper fitment, snap rings and adjustable height not shown
cults3d
Supports to mount Pioneer TS-170ci speakers on bmw e46 coupe front doors, but it may fit other speakers as well. Dimensions are pretty standard. The installation process is straightforward, see pics. Note: the tweeter is friction fitted, if it...
cults3d
Transmission bracket for BMW E36 and some E46 models, it may also serve for another vehicle. The original supports are made of rubber and very expensive, so make this design to be able to print. It also adds solids to the chassis-engine connection,...
thingiverse
I use this to mount a radio for driving tours to communicate with other drivers. I use a battery eliminator for power, an external antenna, and a speaker-mic. The rev1 file fits a little tight, but may be appropriate. rev2 fits looser. ... This...
thingiverse
this is a phone mount for camera tripod for a phone with thickness of 1cm or less but you can scale it up for a bigger phone
grabcad
3D printed Go Pro mounted S7 phone holder, printed on my Form Labs Form 2 printer
thingiverse
This was a phone mount I created and it fits about any phone on the market and can even probably fit your phone case too! ...Fits a good selection of screws that could drill into a 2 by 4.
thingiverse
Mount was designed to be used with a vent mount style phone holder. ...Designed for use with aftermarket radio kit for a ford, may fit others.
grabcad
The Phone Mount allows for the phone to rest on the slanted base of the mount. The mount holds up the phone by little arcs towards the bottom. A little break between the arcs allows for the charger cord to access the port to charge the phone which...
thingiverse
A generic phone mount with screw attachment for universal mounting. By default this design comes with a mic stand adapter, and I'm working on a car adapter. The phone is attached to the adapter with a single M3 screw so the adapter should incorporate...
grabcad
The mount is designed so your phone can simply slide in and out of the mount freely and the mount is very easy to use. The mount would be constructed out of plastic and be able to be 3D printed and easily assembled. It can also be removed and the...
grabcad
The mount is designed so your phone can simply slide in and out of the mount freely and the mount is very easy to use. The mount would be constructed out of plastic and be able to be 3D printed and easily assembled. It can also be removed and the...
thingiverse
Phone Mount with G-Clamp and full rotation. ... no screws required Remix from : https://www.thingiverse.com/thing:2809416 https://www.thingiverse.com/thing:1673030 https://www.thingiverse.com/thing:2448971
thingiverse
Made this cell phone handlebar mount for a family member. He sketched out what he wanted on a scrap of paper and I made it come to life. Models include different length arms to account for different sized phones. Also includes a few different sized...
thingiverse
... is held in place. When it's open the phone simply comes out. It is currently sized to fit an iPhone 6, but is designed with parameters that allow it to be automatically scaled to fit any phone. ... Feel free to remix this into something useful!