eachine 250 3d models

Its made for an Eachine 250, but maybe it will fit on various types...

Diseño para las patas del eachine 250 proteccion para no romper los extremos de las patas

Extrem Motorschutz Eachine 250

arm eachine 250 + motor cover

Tools to dismantle the propellers on a Eachine 250 FPV Racer Post-Printing

Eachine 250 Racer GoPro camera mount, just uses one heavy duty rubber band to hold it in place.

This allows better access for battery by relocating the LED bar to the upper frame of the Eachine 250 Racer (original edition). ...I encased the edges of LED bar to provide some protection on flip-overs, but you will likely need supports on the top...

Gopro's Hard Case Mount for Eachine 250 Racer. Remix from http://www.thingiverse.com/thing:1169338 Its preferible to not use the hard case because of the weight, but at least if you ain't confident flying, your gopro will be as protected as it could...

Anyone that has an Eachine 250 quad racer has probably had the same problem as I have trying to pry the lens cap off. The way the lens is flush mounted makes it a challenge. Then what do you do with it once you get it off. I usually put the cap down...

Eachine 250 GoPro mount 15°

Arm to Body Spacer for The Eachine 250 Racer How I Designed This

Eachine 250 Racer GoPro camera mount has a 15 degree angle, just uses one heavy duty rubber band to hold it in place.

I have a Drone Eachine Racer 250 and make this top frame to get video transmitter, antena, lipo alarm, action cam and more. Always i make improvements. ... See my vídeos at www.Zmaro.com.br with this frame # Print Settings Printer: Geeetech...

Substitution legs for Eachine Falcon 250.

Patins type hélico pour Eachine Fixation par 4 vis / patin de 2,5 mm - longeur 12 mm (en remplacement des vis des suports de bras)

arm for eachine racer 250, racer 250 pro, eturbine TB250

This is a replacement arm for the Eachine Racer 250. It is designed to be stronger than the stock part and with 20% infill and PLA it only weighs 1 gram more than the original. It is also designed so that the arm can be replaced in the field without...

This is a "heavy duty" replacement arm for the Eachine Racer 250. For molded ABS the factory design works well but is very weak when printed. I designed this beefed up arm to be easily printed while remaining strong and lightweight. Cura shows this...

Printet both parts in 0.3 and PLA. Glued them together with Epoxy. To fix the plate on the drone, I used bracelet rubber bands. ...With them, it is easy to remove it.

Back plate for the Eachine Falcon 250. ...Allows to relocate the VTX to a better position.

Mobius action camera mount for eachine racer 250 quadcopter 15 degrees good for 5040 39x37mm holes Added 18 degrees after flying with DAL5045BN Print the first 1.5-2mm with 100% infill.

I do not have a GoPro or something like this mounted on my Eachine Racer 250. So... ...I moved the receiver to the front; however, I didn't like the receiver just hanging out there. ... Thus, I made a 3D printed receiver mount with a "shield" to...

Motor guard modified to fit on an Eachine Falcon 250 Quad copter. Perfect for if you want to remove the 10 degree mounts but keep the protection for the motors. Update. Tested in the field (literally) today and had a pretty big stack. A prop broke...

Simple servo mount for the Eachine Racer 250, this plate will allow you to mount the servo above the flight controller, if you are not using the battery tray that has the same mounting point or want to mount it to the top plate. ...Other items needed...

Second: I am trying to adapt this design to a Eachine Falcon 250 to convert in more actual low frame. **Attention: I do NOT use the Falcon 250 Power Distribution Board (PDB). I use an all-in-one controller (Omnibus F4 clone)** My first problem has...

... if not required for most of them). The Eachine 250's tail end can be shown optionally to see how the antenna holder fits into the frame (frame design is not for printing purposes). ...Prints well in PLA with 40% infill and w/o any support structure.

Eachine, in their infinite wisdom (not) has decided to save pennies and omit the battery tray from this popular budget mini-quad racer.http://wikirotors.com/index.php?title=Eachine_Racer_250#Versions The omission of this part in the newest version 5...

Original post This is a quick and dirty version of the arm used on HMF Totem Q250 and Eachine 250 FPV Racer. Use the treaded inserts from your old arm. I put the bolt in mine and heated them out. To get them in, I put them on an old soldering iron...

These are parts needed to have your FPV camera tilt controlled by a servo on the Eachine 250 FPV Racer. I use it together with a small 3.7g micro servo hooked directly to my RX. I got mine at Banggood. You need to print one of these as well. Or find...

renfort de pied a coller entre les deux joues existantes pour consolider l'ensemble, cette partie est fragile et casse en cas de choc (photo 2).préférez l'impression en ABS pour pouvoir coller ensuite les deux parties entre elles. ...(faire pivoter...