eachine vtx 3d models
7787 3d models found related to eachine vtx.thingiverse
It is designed for the eachine et200 vtx but all small vtx should fit. It has holes for zipties to attach the vtx and a hole on the side to be able to reach the channel switching button. It also works as a protection for the electronics cause it...
myminifactory
Stack mount that fits a 30x30 standard quad mount. ...Put your Eachine 801 VTX in it and have it sit on your stack. UPDATE 12112017: The original design I uploaded somehow lost the bottom portion of the mount. ...I have uploaded a corrected version.
thingiverse
Put your Eachine 801 VTX in it and have it sit on your stack. UPDATE 12112017: The original design (in the pictures) I uploaded somehow lost the bottom portion of the mount. I have uploaded a corrected version. ... ...
myminifactory
Eachine 526 VTX stack mount so that you have a good solution for your 526 to be mounted secure, and on your stack for those shorter frames!
thingiverse
If you can't print this, please consider ordering it through my 3DHub at: http://3dhubs.com/service/8Bit Eachine 526 VTX stack mount so that you have a good solution for your 526 to be mounted secure, and on your stack for those shorter frames!
thingiverse
This bracket holds the Eachine TX805 VTX securely in place. The VTX is mounted using 2 M3 screws. In the bracket there are cutouts to place 4 M3 nuts. The bracket is mounted to the frame with 4 M3 screws. ...There is a slot for the status LEDs and the...
thingiverse
Just a bunch of clip-in holders for the micro camera/video TX module TX06 from Eachine/Banggood. ...
thingiverse
Opened a hole on the bottom to swap channels Flipped the Antenna outlet Moved the FC to VTX port this is my 4th version i'll prob update as needed
thingiverse
A very simple antenna trap to hold the UFL connection. simply slide it on the antenna, then attach the atenna, and slide the trap down over the top of the circuit board. ...pay attention, there is a cutout in the trap to clear the tiny diode thats on...
thingiverse
A Mount for the Turbowing 700tvl DVR micro fpv camera, and Eachine vtx-03. Its meant to be glued into a foam airplane and yet still be removable. you will need 3x 2mm screws roughly 5mm long. size can vary on those. ... Camera can be found in a couple...
thingiverse
This holder camps the VTX of the Eachine TX01S and allows the mounting on the back of the Drone. You can use the original screws. ... There a 2 types - Normal: Can move a little, easy to print without supports - With fixation: Stays in place,...
thingiverse
With this holder you can easily mount the Eachine ET200 VTX on the rear end of the top plate of your quad. This enables you to extend the antenna over the frame. The antenna connector is protected and reinforced with a 3 mm plate and can be fixed...
thingiverse
3 files 1.5mm thick 2mm thick then a prototype i just slimmed down and shaved some extra off(havent used this one)
thingiverse
Soporte para montar el receptor r-xsr de frsky, el vtx eachine 805, la antena en una posición optima, y el buzzer, en el frame del dron. ...
thingiverse
Turning the Eachine E010 into a Cheap Tiny Whoop, by added FX797 / FX798 VTX camera easily with this mount. This mount should work on the Inductrix (Tiny Whoop) too, with only 3 screws. I can print this for you in case you don't have a printer. You...
thingiverse
This is a camera + VTX holder and protector for the Eachine E010S. I couldn't find appropriated version so I started again from the Oscar Liang version made for E010 (the Camera + VTX module is much smaller on E010S). I have the E010S - FrSky...
thingiverse
I modified one of my favorite "whoop" canopies that I designed to hold the Eachine Nano VTX in the top. Mount the VTX with the antenna and button facing the FC. I gave up on Caddx and switched to the Runcam Nano 2 but the screws do not go in as...
thingiverse
This thing was made with Tinkercad. ...Edit it online https://www.tinkercad.com/things/fP0QWFHT1Zw
thingiverse
This thing was made with Tinkercad. ...Edit it online https://www.tinkercad.com/things/dxXwJFa9rgq
thingiverse
I took the work of [nregentet](https://www.thingiverse.com/nregentete) and extended the camera box by 1mm, because mine wouldn't fit. It's funny how 1mm matters so much. ... I've included the stl, as well as the Fusion360 file I used while...
thingiverse
a little case for the Eachine ET200 VTX, simply snaps to the case. i think other vtx will fit also. opening for the channel switch on the side. happy printing... ...if you like it please FOLLOW me or/and give it a LIKE :) , thx Print Settings Printer: ...
thingiverse
Eachine Lizard cam/vtxmount design copied from baddogroberto's design and added andjustable cam angle. first try. ...will make more other mounts.
thingiverse
I have remixt the cover to fit an AKK or eachine VTX in there with a heatsink stiking out. ... Have addet V2 larger holes and complete redesignt do to issues when exporting to STL file should be perfekt Waterproof.
thingiverse
Protezione per Cam/Vtx eachine tx 06. misura 20x20. ... Stampata in PTU infill 100%, risoluzione 1.6